Murdock H2O To Go BF15 Series Скачать руководство пользователя страница 1

 

 

 

 

COMPLIES 

WITH

Member of

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: 

1.800.591.9360

Technical Assistance Fax: 1.626.855.4894

LIMITED WARRANTY - UNITED STATES & CANADA

This warranty does not cover installation or labor charges and does not apply to materials, which have been 
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of 
the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this 
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges 
caused by defects in the materials, or any delay in the repair or replacement thereof.  This warranty is in lieu of 
all other warranties expressed or implied. Product maintenance instructions are issued with each unit and 
disregard or non-compliance with these instructions will constitute an abnormal use condition and void the 
warranty. Stainless steel must be protected on jobsite during construction and must be properly maintained 
after the water has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is 
void.

Murdock warrants that its products are free from defects in material or workmanship under normal use and 
service for a period of one year from date of shipment from the factory. Murdocks’s liability under this warranty 
shall be discharged solely by repair or replacement of defective material, provided Murdock is notified in writing 
within the time periods described above. 

NOTES TO INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished. 
2. Please read this entire booklet before beginning the installation. 
3. Check your installation for compliance with plumbing, electrical and other applicable codes.

LIMITED EXPORT WARRANTY - One year on parts only. 

Murdock™ assumes no responsibility for use 
of void or superseded data. © Copyright 
Murdock Mfg., City of Industry, CA  Member of  
Morris Group International. Please visit 

www.murdockmfg.com

 

for most current 

specifications.

7020-957-001

   

     

Date: 08/02/19

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

Surface Mounted Bottle Fillers

 

BF15 & BF16 Series

Surface Mount Bottle Fillers

MURDOCK

15125 Proctor Ave.

City of Industry, CA

91746 U.S.A.

Phone 800-591-9360

626-336-4561

Fax 626-855-4894

www.murdockmfg.com

 

Federal
Public Law
111-380 
(No Lead)

BF15 Series

BF16 Series

Содержание H2O To Go BF15 Series














Отзывы: