manualshive.com logo in svg

Muratec F-160, Руководство по эксплуатации

Поделиться
Скачать
Muratec F-160 Скачать руководство пользователя страница 14

1.6

Getting started

Pick an installation spot

Where should you install your fax machine? The location should be:
• Clean — Dust buildup can damage your machine. (However, do not use a cover!)
• In the open — Allow at least 12 inches of clearance around your machine. Be

sure that you never cover the machine. Its vents must be able to “breathe.”

• Away from direct sunlight — This helps avoid overheating.
• Dry — Avoid any location where splatters or sprays (such as from a water foun-

tain) could reach your fax machine.

• Level, and vibration-free.
• Near a phone jack — Your fax machine uses a standard (modular) telephone

jack, also known as an RJ-11.

• Near an 

AC

power outlet — The 

AC

power cord is about 5 feet long when

stretched to its limit, and the power cord should never be stretched to its limit.

Power tips

• Use a standard three-pronged 120

VAC

outlet.

• Make sure the outlet isn’t controlled by a wall switch.

If it is, you’ll risk occasional shutoffs to the machine, causing you
to lose fax messages.

• Don’t use an outlet which also is supplying power to a

large appliance, such as a refrigerator or air conditioner.
Such high-consumption appliances can cause “draw-downs”
(temporary drops in the power available for other equipment on
the circuit) which could damage your fax machine.

• Use an electrical surge suppressor, preferably one which guards both tele-

phone and electrical lines. This device helps to shield your fax machine from
damaging high-voltage electrical surges.

Voltage requirements:

120 

VAC

± 10%, 50–60% Hz.

Power consumption:

Standby

Transmission

Reception

Copying

Maximum*

17 

W

40 

W

440 

W

448 

W

650 

W

* ; simultaneous copying, communicating and scanning

Installing the printing supplies

Your fax machine prints incoming faxes and copies with a laser print engine. The
engine requires two types of printing supplies (sometimes also called consumables):
• The drum cartridge — It yields 20,000 normal letter-sized printouts (see “Specifi-

cations,” page 

AI

.1). By “normal,” we’re referring to the amount of text and/or

graphics on each page. This is based on an industry-standard test document.

• The toner cartridge — It yields 5,500 “normal”, letter-sized printouts (see

“Specifications,” page 

AI

.1).

Note: The toner cartridge included with your machine is a starter cartridge which

yields 3,600 printouts (see “Specifications,” page 

AI

.1). Please purchase

regular, full-yield toner cartridges from your authorized Muratec dealer.

To install these supplies:

1

Press the printer cover
release and swing open
the printer cover.

2

Unpack the drum cartridge from its box.

Important: Shield the drum cartridge from light, especially strong

light. Later, if you have to remove the cartridge from the fax,
immediately wrap it in a thick cloth to protect it from light.

3

Put the drum cartridge into the printer
by aligning the cartridge’s protrusions
with the slits inside the printer frame.

Important: You must also reset the

drum counter. See
“Installing a new drum
cartridge” (page 1.7).

Setting up

Содержание F-160



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды