manualshive.com logo in svg

Munters WF54, Инструкция по эксплуатации, Страница: 11 / 20

Поделиться
Скачать
Munters WF54 Скачать руководство пользователя страница 11

11

© Munters Corporation, March 2017

QM1224r3

Electrical Wiring

Chapter 3

3.2 Electrical Wiring

The Munters Drive fan ships configured for simple ON/OFF control.  When electrical power is applied to 

the main cable the fan will start and run at full speed. 

See Figure 9A .

 To operate the Munters Drive On/Off with a control, Slide the ‘ON’ switch, located on the circuit board in 

the junction box, away from the ON position. Now wire an ‘ON’ command from the ‘COMMON’ terminal 
to the input relay in the control and from the output of the control relay to the ‘RUN’ terminal in the junction 
box.  

See Figure 9A & 9B.

When making connections to junction box, be sure to use the supplied watertight fittings with only 1 cable 

per fitting.  If watertight fittings are not used or if 2 cables or more are in 1 watertight fitting, equipment 
failure from water damage will not be covered under warranty.  If 2 or more cables are used in 1 
watertight fitting, they must be sealed on both sides of junction box wall to prevent water infiltration.

‘ON’ Switch

 

Figure 9A

Default Operation Full Speed

Junction Box

‘ON’ Switch

Содержание WF54





















Отзывы:

Нет отзывов