manualshive.com logo in svg

Munters CX24, Инструкция по эксплуатации, Страница: 6 / 14

Поделиться
Скачать
Munters CX24 Скачать руководство пользователя страница 6

© Munters Corporation, May 2020

6

QM1108r0

Installation Instructions

2.

2.1 Fan Installation

Figure 1A

Chain (not provided)

Step 1

 

For Horizontal Airflow attach chain to 2 of the Eye Bolts on the fan and then hang the fan from truss.  

See Figure 1A.  

Chain and hanging hardware not provided.  If it is desired to pull the fan up out of the 

way when not in use for cleaning, then attach a cable or rope to the Lift Bracket and use a winch or 
actuator to pull the fan up.  

See Figure 1B.

Figure 2

Eye Bolt

Chain (not provided)

Eye Bolt

Step 2

 

For Vertical Airflow attach chain to 4 of the Eye Bolts on 

the fan and then hang the fan from trusses.  

See Figure 2.  

Chain and hanging hardware not provided.

Figure 1B

Chain (not provided)

Cable or Rope 
(not provided)

Lift Bracket

If installing fans near heaters, it is 

recommended to install the CX24 Fan at a 
location far enough from heaters that will 
give a maximum temperature of 150°F.  
This should be approximately 2-3 ft. from 
the heater.

IMPORTANT

!

Содержание CX24















Отзывы:

Нет отзывов