background image

© Munters Corporation, July 2021

2

QM1095r1

      Munters ATLAS 74 Fan

 

 

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing an ATLAS 74 Fan. Munters equipment is designed to be the highest performing, highest 
quality equipment you can buy. With the proper installation and maintenance it will provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed 
and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the 

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return  Policy” shall have 

been properly installed, maintained and operated under competent  supervision, according to the instructions 
provided by Munters Corporation.

•  Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation 

or maintenance shall not be considered a defect under the Warranty.

Содержание ATLAS 74



























Отзывы: