MODEL NO LPF60
ASSEMBLY INSTRUCTION
MONTAGE ANLEITUNG
ASSEMBLY INSTRUCTION
MODEL NO LPF60
min30mm-max610mm
m
in
4
7
m
m
-m
a
x
4
2
0
m
m
EN
SAFETY INSTRUCTIONS
PLEASE COMPARE THE PROVIDED MONTAGE MATERIAL AND THE
ILLUSTRATION OF THE SUPPLIED PARTS OF THIS MANUAL.
NEVER USE DEFECTIVE PARTS.
WE DO NOT RESUME LIABILITY FOR RESULTING DAMAGES TO
PROPERTY OR PERSONAL INJURY IF THE PRODUCT HAS BEEN
ABUSED IN ANY WAY OR DAMAGE BY IMPROPER USE OR
FAILURE TO ABSERVE THIS ASSEMBLY INSTRUCTION
-
For safety unauthorized conversion and/or modification
on the device is not permitted.
-
Avoid subjecting the wall bracket to heavy mechanical stress
as declared in this manual.
-
Servicing, adaptation or repair works must only be carried out
by a professional or specialist workshop.
The included hardware is for mounting on solid brick. If the nature of
your wall is deviant, please use equal assembling material. We advise
you to consult a professional for proper mounting.
SUBJECT TO PRINTING ERRORS AND TECHNICAL AMENDMENTS
DE
SICHERHEITSANWEISUNGEN
BITTE VERGLEICHEN SIE DAS MITGELIEFERTE
MONTAGEMATERIAL MIT DEM IN DIESER ANLEITUNG
ABGEBILDETEN LIEFERUMFANG. BENUTZEN SIE NIEMALS
DEFEKTES MONTAGEMATERIAL
WIR ÜBERNHEMEN KEINE HAFTUNG FÜR SCHÄDEN AN
EIGENTUM ODER FÜR VERLETZUNGEN BEI JEGLICHEM
MISSBRAUCH DIESES PRODUKTES ODER FÜR SCHÄDEN, DIE
DURCH UNSACHGEMÄSSE BEHANDLUNG ODER MISSACHTUNG
DIESER MONTAGEANLEITUNG HERVORGERUFEN WERDEN.
-
Der unberechtigte Umbau und/oder das Vornehmen von
Veränderungen am Produkt sind aus Gründen der Sicherheit nicht
zulässig.
-
Setzen Sie die Wandhalterung nicht höherer mechanischer
Belastung aus als angegeben.
-
Wartung, Anpassungen oder Reperaturarbeiten dürfen nur von
Fachkräften oder in einer Fachwerkstatt ausgeführt werden.
Die mitgelieferten Komponenten sind ausschließlich für eine Montage
an einer massiven Stein- und Betonwand geeignet. Sollte die
Beschaffenheit der Wand abweichen, müssen Sie entsprechendes
Montagematerial benutzen. Wir raten Ihnen in diesem Fall eine
Fachkraft für die Montage hinzuzuziehen.
DRUCKFEHLER UND TECHNISCHE ÄNDERUNGEN VORBEHALTEN
IMPORTANT:
Ensure you have received all parts against the component checklist prior to installing. If any parts
are missing or faulty, telephone the special franchiser for a placement.
Warning: A minimum of two qualified people are required for this operation.
• Hook the TV mounted display brackets over the top of the wall plate as shown in fig. 4.1.
• Tighten the safety screws on the display brackets with a proper screw driver.
As shown in fig. 4.1.
Important:
Make sure the TV is correctly hooked and the safety locking screws are locked safely before loosening the TV.
1a WOOD STUD WALL MOUNTING:
WARNING
• Make sure that the supporting surface will safety support the combined load of the equipment and all attached hardware and
components.
• Tighten wood screws firmly, but do not over tighten. Over tightening can damage the screws, greatly reducing their holding power.
• Make sure that mounting screws are anchored into the center of the stunds. Use of an „edge to edge“ stud finder is highly
recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs. Installers are responsible to
provide hardware for other types of mounting situations.
• Wall plate can be mounted to two studs. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is
highly recommended. Based on their edges, draw a vertical line down each stud’s center.
• Place wall plate on wall as a template. And mark the center of the four mounting holes. Make sure that the mounting holes are on the
stud centerline.
• Drill four 1/8” (3mm) dia. Holes 1.2” (30mm) deep, secure it using four lag bolts
(W-A) and four M6 washers (W-C) as shown in fig. 1.1.
1b SOLID BRICK AND CONCRETE BLOCK MOUNTING:
WARNING
• When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8” of actual concrete thickness in the hole to be
used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1” minimum from
the side of the block. It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out
the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and
components.
• Use the wall plate as a template to mark four holes locations on the wall. Two in the top row slots and two more in the bottom row, as
shown in fig.1.2.
• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a concrete anchor (W-B) into each of these holes.
Attach the wall plate to the wall using four lag bolts (W-A) and four M6 washers (W-C), as shown in fig.1.3.
2.Assembling Adapter Brackets
• Screw the safety screws on the adapter brackets as shown in fig.2.1.
3.Installing Adapter Brackets
• To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen.
• Place screen face side down. Place adapter brackets on the back of screen, align to holes, and center on back of screen, as shown
in fig.3.1.
• Attach the adapter brackets to the back of the screen using the appropriate combination of screws, washers, as shown in fig.3.2.
Screw must make at least three full turns into mounting hole and fit snug into place. Do not over tighten.
4 Hang the brackets mounted TV onto the wall plate
Safety instructions
The fixing material supplied is only suitable for walls made from stone, concrete, hollow blocks and solid wood. Walls made from other
materials requires different fixing materials.
