Multitech ISI9234PCIE Скачать руководство пользователя страница 27

Страница: 27 / 66

Chapter 1 – AT Commands, S-Registers, and Result Codes

Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434H)

+ES

Error Control Selection

Description:

Use this command to select the error correction mode. If the modem is operating in
V.80 mode (synchronous buffered mode), and

+ES=,,8,

the

+ES?

will always return

+ES: 6,,8

. The setting of this command overwrites the

command, and the

+ES

command is overwritten by the setting on a

command.

Syntax: AT+ES=<orig_rqst>,<orig_fbk>,<ans_fbk>

Values:

Values Combination

Mode

+ES=1,0,1 Buffered

mode

+ES=0,1,0 Direct

mode

+ES=4,4,6

MNP or disconnect mode

+ES=3,3,5

LAPM or disconnect mode

+ES=4,0,6

MNP or buffered mode

+ES=3,0,2

LAPM, MNP, or buffered mode (Default)

+ES=2,0,2

LAPM or buffered mode

+ES=3,2,4

LAPM, MNP, or disconnect mode

+ES=,,8

V.42 sync buffer mode (V.80 enabled)

+ES=6,,8

V.42 sync buffer mode (V.80 enabled)

Reports

+ES?

Reports current or selected options.

+ES=? Reports

supported

options.

Result Codes:

ERROR

+ESA

Set Up Error Control Parameters

Description:

Sets the control parameters for the DCE in Synchronous Access Mode.

Syntax: AT+ESA=<trans_idle>,<frame_idle>,<crc_type>,<nrzi_en>

Values:

Values Combination

Meaning

+ESA=0,,,,0,0,,

Disables

CRC generation and checking.

+ESA=0,,,,1,0,,

Causes the DCE to generate a 16-bit CRC in the

transmit direction in framed sub-Mode and check the CRC in the receive direction.

<crc_type> Values: 0

Disable CRC generation and checking.

In framed submode, the 16-bit CRC specified in V.42 is generated by the DCE
in the transmit direction and checked by the DCE in the receive direction.

Result Codes:

ERROR

+ETBM

Call Termination Buffer Management

Description:

Sets the behavior of the modem upon call termination. Only

+ETBM=0,0,0

is a valid

combination. This means that the modem will discard all the buffered data when the
call is terminated.

Syntax:

AT+ETBM=<pending_TD>,<pending_RD>,<timer>

AT+ETBM=0,0,0

Values:

<pending_TD>

0 specifies that disconnect will occur immediately and all buffered

transmit data will be discarded when the local DTE requests call
disconnection.

<pending_RD>

0 specifies that disconnect will occur immediately and all buffered
receive data will be discarded when the local DTE requests call
disconnection.

<timer>

0 specifies that the modem will not attempt to deliver the buffered
data before abandoning the attempt and discarding remaining
data.

Reports

+ETBM?

Reports current or selected options.

+ETBM=? Reports

supported

options.

Result Codes:

ERROR

Downloaded from

Elcodis.com

electronic components distributor

Содержание ISI9234PCIE



































































Результаты поиска

Содержание ISI9234PCIE

Отзывы:

Похожие инструкции для ISI9234PCIE

Бренды по названию

Популярные бренды

Multitech ISI9234PCIE, Справочник команд AT

Результаты поиска

Содержание ISI9234PCIE

Отзывы:

Похожие инструкции для ISI9234PCIE

Бренды по названию

Популярные бренды