MULTIQUIP WT5C, Руководство по эксплуатации

Страница: 15 / 54

WT5C SERIES WATER TRAILER • OPERATION MANUAL — REV. #6 (05/28/21) — PAGE 15
COMPONENTS (WATER TRAILER)
1.
Water Tank
— Capacity is 525 gallons (1,987 liters).
Fill with clean water with no debris.
2.
Water Tank Fill Pipe
— 2” diameter steel pipe. Connect
the 2" QD coupler end of this pipe to a fire hydrant.
An interface hose will be required to connect from the
pipe’s QD coupler to the fire hydrant.
3.
Water Tank Cap
— Remove this cap (12-inch diameter
fill port) to fill water tank if using a fire hydrant type
method.
4. Document Box — Storage for documentation and
other information regarding the water trailer.
5.
Tires
— This water trailer uses ST205/75D 14" size
tires. Replace with only recommended type tires. Never
tow water trailer with bad or worn tires.
6. 1.5" CAM and Groove Male QD Port — This port can
be used as either a suction or discharge port depending
on the placement of the manifold control handle.
7.
Manifold Control Handle
— 3-position handle. Allows
3 different modes of operation,
off
,
discharge
or
suction .
8. Garden Hose Drain Valve — When draining of the
water tank is required open this valve to drain water.
9. 2.0" CAM and Groove Male QD Port — This port
(right-side) can be used as either a suction or discharge
port depending on the placement of the manifold
control handle.
10. Garden Hose Valve — When other options of filling
of the water tank are unavailable, a garden hose can
be connected to this valve to fill the water tank. It is
recommended that a rigid walled garden hose or
suction type garden hose be used for this purpose.
In addition this valve can be used as a discharge port
depending on the position of the manifold control lever.
See Table 5.
11.
Spray Bar Control Handle
— 2-position handle, allows
spray bar to be turned either on or off .
12. Drain Plug — Remove this plug to drain water from
the pump.
13.
Fill Cap
— Prior to operation, the pump casing should
be filled with water. Remove this cap to add water to
the pump. After the initial prime, a sufficient amount of
water will be retained in the casing so that the operator
will not need to re-prime later.
14.
Coupler Adapters
— see Coupler Types section under
Trailer Guidelines.
15.
Hydraulic Brake Actuator
— This actuator (Series
WT5C only) will be activated in the event of a
breakaway. The breakaway cable must be rigged to the
tow vehicle with appropriate slack that will activate the
system if the coupler connection comes loose.
16.
Electric Brake Actuator
— This actuator (Series
WTE5C only) will be activated in the event of a
breakaway. The breakaway cable must be rigged to the
tow vehicle with appropriate slack that will activate the
system if the coupler connection comes loose.
17.
Engine
— This water trailer uses a Honda GX120UT3PX2,
3.5 HP, air-cooled, 4-stroke, single-cylinder gasoline
engine.
18.
2.0" CAM and Groove Male QD Port
— This port
(left-side) can be used as either a suction or discharge
port depending on the placement of the manifold
control handle.
19. Dust Cap — There are 3 dust caps that are used
with the manifold system. These caps prevent dirt
and debris from entering the water system when the
suction/discharge hoses are not connected.
20. Spray Nozzles — Located at the rear of the water
trailer are two water spray nozzles. These nozzles can
operate under multiple pressure settings.
21.
Storage Bin
— Place hoses and accessories in this
bin during transport.
22.
License Light
— This light illuminates the license plate.
Whenever towing of the light tower is required, make
sure this light is operational.
23.
Brake Lights
— Before towing the water trailer, make
sure that these lights are operational and are working
correctly. Never tow the water trailer if these lights are
inoperative.
24. Low Point Drain Valve — A standard garden hose bib
located underneath manifold.