MULTIQUIP Whiteman J36H55 Скачать руководство пользователя страница 18

Страница: 18 / 70

PAGE 18 — J36/M30 WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #10 (05/07/12)

Figure 4. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation.  Refer to the manufacturer's engine
manual for  instructions & details of operation and servicing. The
engine shown above is  a

HONDA

engine, operation for other

types of engines may vary somewhat.
1

Fuel Filler Cap –

Remove this cap to add unleaded

gasoline to the fuel tank. Make sure cap is tightened

securely.

DO NOT

over fill.

BASIC ENGINE

Throttle Lever –

Used to adjust engine RPM speed (lever

advanced forward

SLOW

, lever back toward operator

FAST

Engine ON/OFF Switch –

position permits engine

starting,

OFF

position stops engine operation.

Recoil Starter (pull rope) –

Manual-starting method. Pull

the starter grip until resistance is felt, then pull briskly and

smoothly.

Air Cleaner –

Prevents dirt and other debris from entering

the fuel system. Remove wing-nut on top of air filter

cannister to gain access to filter element.

11.

Oil Drain Plug –

Remove this plug to remove oil from the

engine's crankcase.

12.

Dipstick/Oil Filler Cap –

Remove this cap to determine if

the engine oil is low. Add oil through this filler port as

recommended in Table 4.

Choke Lever –

Used in the starting of a cold engine, or in

cold weather conditions. The choke enriches the fuel

mixture.

. Fuel Tank –

Holds unleaded gasoline. For additional

information refer to engine owner's manual.

Muffler –

Used to reduce noise and emissions.

Spark Plug –

Provides spark to the ignition system. Set

spark plug gap according to engine manufacturer's

instructions. Clean spark plug once a week.

Fuel Valve Lever –

OPEN

to let fuel flow,

CLOSE

to stop

the flow of fuel.

Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill,

DO NOT

attempt to start the engine until

the fuel residue has been completely wiped
up, and the area surrounding the engine is dry.

DANGER

Operating the engine without an air filter, with a damaged

air filter, or a filter in need of replacement will allow dirt to

enter the engine, causing rapid engine wear.

NOTICE

Содержание Whiteman J36H55







































































Результаты поиска

Содержание Whiteman J36H55

Отзывы:

Похожие инструкции для Whiteman J36H55

Бренды по названию

Популярные бренды

MULTIQUIP Whiteman J36H55, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Whiteman J36H55

Отзывы:

Похожие инструкции для Whiteman J36H55

Бренды по названию

Популярные бренды