MULTIQUIP Stow MS-93, Руководство по эксплуатации и запасным частям

Страница: 16 / 92

PAGE 16 — STOW MS-93 MIXER — OPERATION MANUAL — REV. #5 (03/26/10)
STOW MS-93 PLASTER/MORTAR MIXER — BASIC MIXER COMPONENTS
Figure 5. Mixer Components
1.
Tires Ply
— The tire ply (layers) number is rated in letters;
This mixer uses 13-inch 4-ply tires.
2.
Engine Cover
— Lift this cover to gain access to the
engine compartment.
3.
Belt Slip Lever
— When starting this lever should be
move upward and to the left. For mixing place the lever in
the down position. See attached decal located adjacent
to lever.
4.
ON/OFF Switch (electric)
— This switch is provided on
mixers with electric motors. To gain access to this switch,
lift the engine cover. When activated it will shut down the
electric motor.
5. ON/OFF Switch (gasoline) — This switch is provided
on mixers with gasoline engines only and is located on
the side of the engine cover. When activated it will shut
down the engine.
6. Latch — Use this latch to secure the engine compart-
ment cabinet.
7. Drum Bearing — There is on each end of the mixing
drum, a sealed bearing. Bearings are packed and sealed
at the factory and require no further maintenance.
Figure 5 illustrates the basic components and controls of
the STOW MS-93 mixer
8.
Mixing Paddles
— Used in the mixing of material. This
unit uses four different types of paddles to provide a fast
uniform mix.
9. Bag Cutter — This feature allows compound mixing bags
to be opened easily, therefore allowing the contents of
the bag to fall directly into the mixing drum.
10. Safety Grill — Provided for operator safety. This safety
grill is designed to keep hands and solid objects out of
the mixing drum when in use. This grill should be closed
at all times when mixer is in use.
DO NOT
remove the
grill or grill opening bar. Keep the grill clean by washing
it down daily.
11.
Dump Handle
— Pull this handle downward to dump the
contents of the drum. Push the handle upward to return
the drum to its vertical position.
12.
Safety Grill Lock Handle
— To prevent injury to hands
and arms, the safety grill should
ALWAYS
be locked when
the mixing of plaster or mortar is required. Also when
transporting the mixer the safety grill should be locked.
The safety grill should only be un-locked when cleaning
of the blades and drum is required.
13. Pivot Point/Zerk Fitting — There is, on each end of the
mixing drum a zerk grease fitting. These fittings lubricate
the dumping mechanism. Lubricate both fittings at least
twice a week.
14. Dump Handle Release Pin — Pull this pin outward
(spring loaded) to release the drum, then pull down on
the dump handle to place the drum in the dump position.
When drum is in dump position, pin will automatically lock
drum.
15.
Steel Mixing Drum
— Mixing materials such as mortar,
plaster are to be placed into this drum for mixing. Always
clean the drum after each use.
16.
Tow Bar/Coupler
— This mixer uses a 2-inch coupler
or pintle towbar.
17.
Safety Chain
— This mixer uses a 3/16-inch thick,
72-inches long zinc-plated saftey chain.
AlWAyS
con-
nect the safety chain when towing.
18.
Forklift Pockets – When lifting of the mixer is required,
use these fork lift pockets to lift the mixer. Remember to
insert the forks of the forklift a minimum of 24 inches
into the lift pockets.
19.
Chock Blocks
— Place these blocks (not included as
part of the mixer package) under each mixer wheel to
prevent rolling.