QP-305SLT TRASH PUMP — OPERATION & PARTS MANUAL— REV. 0 (03/22/05) — PAGE 13
Figure 2 shows a typical application using the QP-305SLT centrifugal pump. Please note that this pump is intended for the removal
of clean water and water containing some debris and solids. Maximum size of solids should not exceed 1 inch (25 mm) in diameter.
DO NOT
set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump from drawing in
excessive amounts of sand and foreign debris.
6
.
Pump –
The model QP-305SLT is 3-inch centrifugal pump
and should only be used in only
clear water
applications
(agricultural, industrial, residential) as they have a limited
soild handling capability of only 10% by volume.
7
.
Drain Plug –
Remove this plug to drain water from the
pump.
8
.
Suction Hose –
Connect a flexible rubber hose to the
suction port on the pump. Make sure that the hose lays flat
and is not kinked. Use only recommended type suction
hose. Contact Multiquip parts department for ordering
information
9
.
Strainer –
Always attach a strainer to bottom side of the
suction hose to prevent large objects and debris from
entering the pump. Strainer should be positioned so that it
will remain completely under water. Running the pump with
the strainer above water for long periods can damage pump.
Figure 2. QP-305SLT Pump Application
QP-305SLT — PUMP COMPONENTS
1
.
Discharge Port 1.5-Inch –
Connect a flexible rubber hose
to this 1.5-inch discharge port (1) on the pump. Make sure
that the hose lays flat and is not kinked. Use only
recommended type discharge hose. Contact Multiquip parts
department for ordering information.
2
.
Discharge Port 1-Inch –
Connect a flexible rubber hose
to these 1-inch discharge ports (2) on the pump. Make sure
that the hose lays flat and is not kinked. Use only
recommended type discharge hose. Contact Multiquip parts
department for ordering information.
3
.
Fill Cap –
Prior to operation, the pump casing should be
filled with water. Remove this cap to add water to the pump.
After the initial prime, a sufficient amount of water will be
retained in the casing so that the operator will not need to
re-prime later.
4
.
Worm Clamp –
Used to secure the hose to the inlet and
outlet ports on the pump. Use two clamps to secure the
hose on the inlet side of the pump.
5
.
Discharge Hose –
Connect a flexible rubber hose to the
discharge port on the pump. Make sure that the hose lays
flat and is not kinked. Use only recommended type discharge
hose. Contact Multiquip parts department for ordering
information.
Содержание QP305SLT
