MULTIQUIP Power WHISPERWATT DCA70USI2 Скачать руководство пользователя

Страница: 11 / 84

DCa70USI2 60 hz generaTor • operaTIon anD parTS manUal — rev. #0 (06/28/11) — page 11

safetY infOrMatiOn

BaTTerY SaFeTY

Danger

Do noT drop the battery. There is a possibility that the

battery will explode.

Do noT expose the battery to open fl ames,

sparks, cigarettes, etc. The battery contains

combustible gases and liquids. If these

gases and liquids come into contact with a

fl ame or spark, an explosion could occur.

WarnIng

alWaYS wear safety glasses when handling

the battery to avoid eye irritation. The battery

contains acids that can cause injury to the

eyes and skin.

Use well-insulated gloves when picking up the battery.

alWaYS keep the battery charged. If the battery is not

charged, combustible gas will build up.

alWaYS recharge the battery in a well-ventilated

environment to avoid the risk of a dangerous concentration

of combustible gasses.

If the battery liquid (dilute sulfuric acid) comes into

contact with

clothing or skin, rinse skin or clothing

immediately with plenty of water.

If the battery liquid (dilute sulfuric acid) comes into

contact with

eyes, rinse eyes immediately with plenty

of water and contact the nearest doctor or hospital to

seek medical attention.

CaUTIon

alWaYS disconnect the negaTIve battery terminal

before performing service on the generator.

alWaYS keep battery cables in good working condition.

Repair or replace all worn cables.

envIronmenTal SaFeTY

NOTICE

Dispose of hazardous waste properly.

Examples of potentially hazardous waste

are used motor oil, fuel and fuel fi lters.

Do noT use food or plastic containers to

dispose of hazardous waste.

Do noT pour waste, oil or fuel directly onto the ground,

down a drain or into any water source.

Содержание Power WHISPERWATT DCA70USI2





















































































Результаты поиска

Содержание Power WHISPERWATT DCA70USI2

Отзывы:

Похожие инструкции для Power WHISPERWATT DCA70USI2

Бренды по названию

Популярные бренды

MULTIQUIP Power WHISPERWATT DCA70USI2, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Power WHISPERWATT DCA70USI2

Отзывы:

Похожие инструкции для Power WHISPERWATT DCA70USI2

Бренды по названию

Популярные бренды