MULTIQUIP MAYCO LS300G Скачать руководство пользователя страница 77

Страница: 77 / 90

MAYCO LS300G CONCRETE PUMP • OPERATION MANUAL — REV. #2 (09/09/19) — PAGE 77

Troubleshooting (Gasoline Engine) - continued

Symptom

Possible Problem

Solution

Low engine power output and low speed,

black exhaust smoke.

Air fi lter blocked?

Clean or replace air fi lter.

Incorrect valve clearances?

Adjust valves per engine specifi cation.

Engine overheats.

Too much oil in engine crankcase?

Drain off engine oil down to uppermark on
dipstick.

Entire cooling air system contaminated/

blocked?

Clean cooling air system and cooling fi n

areas.

Fan belt broken or elongated?

Change belt or adjust belt tension.

Coolant insuffi cient?

Replenish coolant.

Radiator net or radiator fi n clogged with dust? Clean net or fi n carefully.
Fan, radiator, or radiator cap defective?

Replace defective part.

Thermostat defective?

Check thermostat and replace if necessary.

Head gasket defective or water leakage?

Replace parts.

Engine oil pressure display stays on.

Faulty engine oil pressure switch?

Contact your nearest MQ service center.

No or low level of engine oil?

Check and adjust oil level as necessary.

Clogged engine oil fi lter

Replace engine oil fi lter.

Engine coolant display turns on.

Low engine coolant level?

Add engine coolant.

Dirty radiator fi ns?

Clean radiator fi ns.

Engine coolant leaking?

Contact your nearest MQ service center.

V-Belt loose or damaged?

Adjust or replace V-belt.

Contaminated engine coolant?

Contact your nearest MQ service center.

Faulty engine coolant pump?

Contact your nearest MQ service center.

Battery indicator display turns on.

V-belt loose or damaged?

Adjust or replace V-belt.

Battery Failure?

Check battery condition.

Faulty Alternator?

Contact your nearest MQ service center.

TROUBLESHOOTING (ENGINE)

Содержание MAYCO LS300G



























































































Результаты поиска

Содержание MAYCO LS300G

Отзывы:

Бренды по названию

Популярные бренды

MULTIQUIP MAYCO LS300G, Руководство по эксплуатации

Результаты поиска

Содержание MAYCO LS300G

Отзывы:

Бренды по названию

Популярные бренды