Operating Instructions for Power Set
„AcroMaster“ and „Gemini TUNING“
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 2/2
Operati
on in
stru
ctio
ns
for
Po
wer
set „A
croMa
s
ter
“ and
„G
e
m
ini TUNI
NG“
#
8
2
6007
(08-02-2
6
/DAMA)
E
rror
s
a
nd
omissi
ons e
x
cepte
d!
©
M
U
LTIPLEX
6. I
NITIATION OF THE
P
OWER
S
ET
“A
CRO
M
ASTER
”
AND
“G
EMINI
TUNING”
1. Connect the three wires attached to the speed control-
ler to the three wires attached to the motor; the order of
connection is unimportant.
2. Locate the UNI connector attached to the speed con-
troller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the “OFF” position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking for-
ward. If this is not the case, disconnect the flight battery
and swap over any two of the three motor wires.
6. Switch off the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
7. H
IMAX
M
OTOR
-
S
PECIFICATION
Type: C
3516-1130
# 33
3023
RPM / V:
1130
Cell count, NiXX / LiPo:
6 - 9 / 2S - 3S
Efficient operating current:
10 A - 34 A
Max. current for 15 sec.:
48 A
Shaft Ø
:
5.0 mm
Diameter: 35
mm
Length: 42
mm
Weight: 134
g
Max. output:
350 W
Max. case temperature:
65
°
C
Mounting:
25 mm Ø / 4 x M3
You will find comprehensive operating instructions for the
Himax C 3516-1130 at www.multiplex-rc.de
Æ
DOWNLOADS
Æ
INSTRUCTIONS.
8. G
UARANTEE
MULTIPLEX products are covered by the statutory guar-
antee regulations. If you wish to make a claim under
guarantee, please contact the model shop where you
purchased the product in the first instance.
The guarantee does not cover damage and malfunctions
caused by:
•
Improper handling, incorrect connections,
reversed polarity
•
Use of accessories other than genuine MULTIPLEX
items
•
Modifications or repairs not carried out by MULTIPLEX
or an authorised MULTIPLEX Service Centre
•
Accidental or deliberate damage
•
Defects due to normal wear and tear
•
Use outside the technical specifications
9. CE
A
PPROVAL
This product satisfies all the relevant statutory
harmonised EU directives.
You are therefore the owner of a product whose design
fulfils the protective aims of the European Community
relating to the safe operation of equipment.
You are entitled to obtain a copy of the conformity
declaration for this product by contacting MULTIPLEX
using the information at the foot of the page.
10. D
ISPOSAL
I
NFORMATION
Electrical equipment marked with the cancelled
waste bin symbol must not be discarded in the
standard household waste; instead it must be
taken to a suitable specialist disposal system.
In the countries of the EU (European Union), electrical
equipment must not be discarded via the normal domestic
refuse system (WEEE – Waste of Electrical and
Electronic Equipment, directive 2002/96/EG). You can
take unwanted equipment to your nearest local authority
waste collection point or recycling centre, where the items
will be disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the environ-
ment.