Multikomplex S-DD11-L, Инструкция по установке, использованию и обслуживанию

Страница: 24 / 30

S-DD
11
-
L
20
EN
MODEL SDD2-L GLASS VERSION
A: Light ON/OFF key
The light switches on and off only when the
carriage is fully OPEN.
Pressing this button with the carriage closed
will cause the carriage to open and then the
light will switch on .
The button also serves to switch off the light
if it is on.
B: ON/OFF key
This starts the extraction carriage upward
movement and when it is fully open, it sets the
second extraction speed.
With the carriage open: it switches off the mo-
tor and if on, the light; then it retracts the ex-
traction carriage.
C: (-) Key
This reduces the speed of the extractor motor
from the 4th
speed until the motor switch-
es off, without closing the pull-out car-
riage
.
D: Indicators
• This signals the speed setting, by only the
relevant LED switching on.
• This signals that all filters have been satu
-
rated by all LEDs switching on.
E: (+) Key
This increases the speed of the extractor mo-
tor, from 1st to 4th speed, without moving the
extractor panel.
F: Timer
10 min after setting, it serves to stop the ex-
tractor motor, close the carriage and switch
the lights off, if they are on. The set function is
signalled by the flashing LEDs “D” for the set
speed. The timer can be cancelled by press-
ing the key again.
Other functions:
Automatic turn off:
After 4 hours of continuous working from the
last setup, the appliance turns off and closes
automatically.
Grease filters saturation:
After 30 hours of working, the speed indica-
tors “
D ” will all flash simultaneously, signaling
the grease filters saturation.
To reset this alarm, hold down the “
TIMER ”
button for at least 3 seconds, while the car-
riage is open.
Calibration:
The cooker-hood carries out its self-calibra-
tion every 3 complete cycles of its extractable
unit.
By pushing the “
TIMER ” key 6 times consec-
utively (MAX break between one push and the
other is 3 sec.) all the leds will flash and the
calibration will be reset.
After the next 3 cycles the downdraft will carry
out its self-calibration.
Stand-by:
When the extractable unit is closed and the
light is switched off, the control panel, after
6 seconds, activates the Stand-by function,
reducing the brightness of the leds.
This function can be stopped by pressing
ON/
OFF or LIGHT key.
HOW THE COOKER
HOOD WORKS
6- key push button panel ( fig. 12)
A: Light ON/OFF key
B: Motor ON ( I speed ) /OFF key
C: II speed key
D: III speed key
E: IV speed key
F: 10 minutes timer
The extractable unit is open manually by pu-
shing the glass downwards, as shown in figure
4; in the same way, push the glass downwards
to close it, until it is completely closed .
The motor and the lights are started by the push
button panel (fig.12).
The motor and the light are automatically
switched off when the extractable unit is closed,
in case they are on.
Other functions:
Automatic turn off:
After 4 hours of continuous operation from the
last setup, the appliance turns off automatically.
Grease filters saturation:
After 30 hours of operation, the speed indica
tors “D” will all flash simultaneously, signaling
the grease filters saturation. To reset this alarm,
hold the “TIMER” button down for at least 3 se-
conds, while the extractable unit is open.
6- key push button panel ( fig. 12)
A: Light ON/OFF key
B: Motor ON ( I speed ) /OFF key
C: II speed key
D: III speed key
E: IV speed key
F: 10 minutes timer
The extractable unit is open manually by pu-
shing the glass downwards, as shown in figure
4; in the same way, push the glass downwards
to close it, until it is completely closed .
The motor and the lights are started by the push
button panel (fig.12).
The motor and the light are automatically
switched off when the extractable unit is closed,
in case they are on.
TIMING
As a result of the new EU65 “Energy label” and
EU66 “ Ecodesign” regulations issued by the
European Commission, which came into force
as from January 1st, 2015 , our products have
been adapted to comply with these new requi-
rements.
All of the models complying with the energy label
requirements, are equipped with new electroni-
cs including a timer device for suction speeds
control, when the air capacity exceeds 650m
³
/h.
Internal motor models, with maximum air capa-
city higher than 650m
³
/h, are equipped with a ti-
mer device that automatically switches the suc-
tion speed from 4th to 3rd speed, after 6 minutes
operation.
External motor models are equipped with remo-
te motors that , as for internal motor versions,
include a timer device that switches down the
suction speed when it exceeds 650 m
³
/h. (See
External Motors Instructions )
Remote motors, whose air capacity exceeds
650m
³
/h at both 4th and 3rd speed , will have
the following by default timer control functions:
The suction speed is automatically switched
from 4th to 2nd speed, after 6 minutes operation.
If the appliance is working at 3rd speed, it is au-
tomatically switched to 2nd speed, after 7 mi-
nutes operation. Operation speeds can also be
changed during operation.
The energy consumption of the appliance in
stand – by mode is lower than 0.5W.
Other functions:
Automatic turn off:
After 4 hours of continuous operation from the
last setup, the appliance turns off automatically.
Grease filters saturation:
After 30 hours of operation, the speed indica
tors “D” will all flash simultaneously, signaling
the grease filters saturation. To reset this alarm,
hold the “TIMER” button down for at least 3 se-
conds, while the extractable unit is open.