User Manual: VersoClub-HT3012
V2.00 (01-2014)
14
A4 (fading) | A14 (switching) | S4 (S2L fading) | S14 (S2L switching)
A color-fill/Blink pattern. Transition is switching in Switch Pattern mode, and
fading in Fade pattern mode.
A5 (fading) | A15 (switching) | S5 (S2L fading) | S15 (S2L switching)
A Fork22 pattern with all 4 panels on. Transition is switching in Switch Pattern
mode, and fading in Fade pattern mode.
A6 (fading) | A16 (switching) | S6 (S2L fading) | S16 (S2L switching)
A 1C Pingpong pattern. Transition is switching in Switch Pattern mode, and
fading in Fade pattern mode.
A7 (fading) | A17 (switching) | S7 (S2L fading) | S17 (S2L switching)
A 4C Pingpong pattern. Transition is switching in Switch Pattern mode, and
fading in Fade pattern mode.
A8 (fading) | A18 (switching) | S8 (S2L fading) | S18 (S2L switching)
A Frame22 pattern. Transition is switching in Switch Pattern mode, and fading
in Fade pattern mode.
A9 (fading) | S9 (S2L fading) | S19 (S2L switching)
A 4-step pattern. Transition is switching in Switch Pattern mode, and fading in
Fade pattern mode.
A19 (swstrobe) :
A Strobe pattern. All panels strobe at the same time, with alternating colors.
A20: white strobe
A21: red strobe
A22: green strobe
A23: blue strobe
DMX Modes
Press the MODE button on the unit itself until the display shows any of the below
options, which are displayed consecutively, indicating operation in the chosen DMX
mode. You then can choose any DMX starting address by simply using the UP/DOWN
buttons on the unit itself. The chosen DMX-address becomes effective approximately 3
seconds later and will show up on the display on the unit itself in alternation to the
indicator of the chosen mode. This allows control of the unit by any external DMX signal
sending on the chosen channels. Once such signal is received, a LED on the lower
right side of the “d” in the display indicates that a DMX signal is present. Once in “d”
Mode, the IR remote control sensor is disabled. Also note that DMX functions cannot
be activated via the optional IR remote.
User Manual: VersoClub-HT3012
V2.00 (01-2014)
7
When using a tripod, make sure that:
•
the tripod is erected to a height where the audience can neither accidently nor
intentionally touch it
•
the working height is in enough distance to ceiling or other constructions on top to
avoid any heat accumulation
•
the working load of the used tripod is sufficient to carry this unit. Do only use
safety-certified tripods.
•
the tripod has a locking mechanism against unintentional tube retraction.
•
the tripod stands on even and firm ground.
•
any cable running to and from the trip is not obstructing pathways of the audience,
and that no any pull force on a cable can make the tripod fall over.
•
the tripod base is either out of audience reach or gated with a security fence
•
the tripod is placed outside of any evacuation paths.
Risk of injury:
Tripod mounting requires related knowledge and
experience, including among others calculating and balancing working
load limits, correct positioning and securing, and periodic safety
inspection. Improper installation can result in body injury. The
manufacturer of this unit does not assume any liability for correct and
secure placement and use of tripods – make sure to comply with local
safety regulations.
Hanging/Rigging, ceiling-mounted operation
Further to the tripod mounting adaptor, the VersoClub-HT3012 is equipped with two
M10 thread insert mounting points on the top of the unit. These can typically be used to
insert truss hooks or other rigging equipment.
Risk of injury:
Overhead mounting requires extensive experience,
including among others calculating working load limits, good knowledge
of the installation material being used, and periodic safety inspection of
all installation material and the unit. If you lack such qualifications, do
not attempt the installation yourself. Improper installation can result in
body injury. Be sure to complete all rigging and installation procedures
before applying power to the unit.
•
The unit should be installed out of reach of people and outside areas where
persons may walk by or be seated.
•
Make sure that the installation area can hold a minimum point load of 10 times the
device’s weight.
•
In fixed installations, fix the unit with self-locking screws/nuts to the mounting point.
•
When mounting the unit to truss be sure to secure an appropriately rated clamp to
the hanging yoke using a M10 screw fitted through the center hole of the hanging
yoke.
