Muirhead 3565 Скачать руководство пользователя страница 12

Страница: 12 / 28

12 | 28

M0160.docx | Rev 1.3 | Modified on 19/05/2020 | © Remote Control Technologies Pty Ltd

Coolant Level Sensor – Function 1

It is recommended that the coolant level sensor be installed in the radiator tank (refer to the details below).

Ensure there is sufficient clearance within the radiator to accommodate the length of the coolant. Drill the

required hole size in the tank and tap to the required thread size as specified below. Always clean debris away

and remove any foreign objects before installing the probe. Fit the coolant level sensor and pressure test, this

can be achieved by running the engine until normal operating temperature has been reached.

Engine Oil Pressure Switch – Function 2

The engine oil pressure switch should be in a suitable oil gallery access port. Use the original equipment

manufacturer (OEM) oil pressure switch as a guide for location. Fit the oil pressure switch using thread sealant,

being careful not to over tighten.

Note

T-pieces are available in most thread types to enable both the OEM and Muirhead

Oil Pressure Switches to

be installed into the original port.

Part No. 0018

12 PSI

Normally Open

Thread: 1/8 NPT

Part No. 3074

8 PSI

Normally Open

Thread: 1/8 NPT

Part No. 8725

9 PSI

Normally Open

Thread: 1/8 NPT

Part No. 9976

12 PSI

Normally Open

Thread: 9/16 UNO

Part No. 3429

16 PSI

Normally Open

Thread: 1/8 NPT

Part No. 3430

9 PSI / 62 kPa

Normally Open

Thread: 1/8 NPT

Radiator

Installation Example

Probe Position

Optimum probe level is

⅓

up from the bottom of the

top hose hole.

Part No. 2006

Thread: 1/8 NPT

Nylon

Tapping drill: 21/64”

Probe length: 30 mm

Part No. 2887

Thread: 1/4 NPT Nylon

Tapping drill: 7/16”

Probe length: 72 mm

Note:

Brass weld

collar included

Part No. 2205

Thread: 1/4 NPT Brass

Probe length: 60 mm

Tapping drill: 7/16”

Содержание 3565





























Результаты поиска

Содержание 3565

Отзывы:

Бренды по названию

Популярные бренды

Muirhead 3565, Руководство по эксплуатации продукта

Результаты поиска

Содержание 3565

Отзывы:

Бренды по названию

Популярные бренды