3
MTA3004-EX 4 Foot Extension Kit for Liberty
WARNING!
Read all assembly, field assembly and safety instructions associated with the Liberty Tripod prior to using this product.
Failure to follow these instructions and warnings may result in serious injury or death!
IMPORTANT NOTES:
These instructions assume you have fully assembled your existing MTP3000 Liberty Tripod. Please keep all existing hardware;
instructions may require you to remove it temporarily but all parts will be required for complete assembly. To ensure proper fit,
finger tighten all nuts and bolts until instructed to fully tighten.
STEP 1.
Remove the
adjuster legs
(Fig. 1), then attach the
leg extensions
to the
bottom legs
using (2) 5/16” x 2 1/4” hex bolts [D] (4) nylon
washers and (2) 5/16” nylock nuts to secure. Insert the
adjuster legs
into the
leg extensions
and secure at desired height using (2) snap pins.
(Fig. 2)
STEP 2.
Next, loosen and remove the existing hardware securing the
x-supports
to the
bottom ladder section
and
bottom legs
. (Fig. 2)
STEP 3.
Remove the existing hardware and
bottom ladder section
, then attach the
ladder section extension
to the
middle ladder section
using (2) 1/4” x 1 1/2” hex bolts [B], (2) nylon washers and (2) 1/4” nylock nuts to secure. Secure the
bottom ladder section
to the
ladder section
extension
using existing hardware. (Fig. 2)
STEP 4.
Assemble the (3)
cross supports
by inserting (3)
male supports
into (3)
female supports
and secure using (3) 1/4” x 1 1/4” hex bolts
[A], (3) nylon washers and (3) 1/4” nylock nuts. (Fig. 3)
STEP 5.
Next, assemble the (4)
stabilizers
by inserting (8)
male supports
into (4)
support connectors
using (8) 1/4” x 1 1/4” hex bolts [A], (8)
nylon washers and (8) 1/4” nylock nuts to secure. (Fig. 4)
STEP 6.
Using (2) 5/16’’ x 3’’ hex bolts [E], (4) nylon washers and (2) 5/16’’ nylock nuts secure (1)
cross support
, (2)
stabilizers
and existing
x-supports
to the rear brackets on the existing
bottom legs
. Then, attach the
stabilizers
to the
leg extensions
using existing hardware. (Fig. 5)
STEP 7.
Secure the assembled
stabilizers
by aligning holes and using (1) 1/4” x 2 1/4” hex bolt [C], (2) nylon washers and (1) 1/4” nylock nut to
secure. (Fig. 5)
STEP 8.
Attach (2)
cross supports
, (2)
stabilizers
and existing
x-supports
to the front brackets on the existing
bottom legs
using (2) 5/16’’ x
3’’ hex bolts [E], (4) nylon washers and (2) 5/16’’ nylock nuts secure. Then, attach the
stabilizers
to the existing
bottom ladder section
using
existing hardware. (Fig. 6)
Parts List (MTA3004-EX)
Part#
Description
Qty
UP15-0265
Ladder Section Extension
1
UP15-0266
Leg Extension
2
UP15-0267
Male Support
11
UP15-0268
Female Support
3
UP15-0269
Support Connector
4
UP15-0405
Instruction Manual
1
Hardware Pack
UP77-0018
[A] 1/4'' x 1 1/4'' Hex Bolt
11
UP77-0019
[B] 1/4" x 1 1/2" Hex Bolt
2
UP77-0023
[C] 1/4'' x 2 1/4'' Hex Bolt
1
UP77-0044
[D] 5/16'' x 2 1/4'' Hex Bolt
4
Parts List (MTA3004-EX)
Part#
Description
Qty
UP77-0048
[E] 5/16'' x 3'' Hex Bolt
4
UP77-0001
1/4'' Nylock Nut
14
UP77-0029
5/16'' Nylock Nut
8
UP77-0030
Nylon Washer
27
TOOLS Required
for Assembly
Adjustable Wrench
(Not Included)
Qty
2
MTA3004-EX
SPECIFICATIONS
For use with MTP3000
The Liberty
Adjuster
Leg
Adjuster
Leg
Snap Pin
Snap
Pin
Adjuster
Leg
Leg
Extension
Leg
Extension
Middle
Ladder
Section
B
Bottom
Ladder
Section
Ladder
Section
Extension
Bottom
Leg
Adjuster
Leg
D
D
B
Uses existing hardware
*
MTA3004-EX FIG 1
MTA3004-EX FIG 2
