READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the Treestand Manufacturers Association’s TMS 04 -
Standard Practice for Treestand Instructions
and TMS 02 -
Standard Test Method for Treestand Fall Arrest Systems.
attEntIon!!
WHEn You sEE a “ WarnInG!” BE surE to HEED tHE MEssaGE!
tHE InForMatIon contaInED In tHEsE MEssaGEs can saVE Your lIFE!!
5
HarDWarE
Part #
Description
qty
UP15-0239
Top Section
1
UP15-0240
Middle Section
3
UP15-0241
Bottom Section
1
UP14-0089 U-Brackets
5
UP10-0037
Support Straps
5
UP15-0331
Tube Plug
42
UP15-0398
Instruction Manual
1
Part #
Description
qty
UP77-0039 5/16 x 1 3/4" Hex Bolt
10
UP77-0031 5/16" Steel Washer
20
UP77-0029 5/16" Nylock Nut
10
UP77-0030 Nylon Washer
24
UP77-0158
1/4'' x 1 1/2'' Swedge Bolt
4
UP77-0001 1/4" Nylock Nut
4
Parts lIst
sPEcs
tools rEquIrED:
Adjustable Wrench - Qty 2 (Not included)
Minimum/Maximum tree Diameter
9” min. and 20” max. at installation height (i.e., seating platform height)
Maximum occupancy:
ONe (1)
Max. Weight capacity (user and Equipment):
300 lbs/136 kg
Part #
Description
qty
Part #
Description
qty
UP77-0039 5/16 x 1 3/4” Hex Bolt
10
UP77-0030 Nylon Washer
24
UP77-0029 5/16” Nylock Nut
10
UP77-0001 1/4” Nylock Nut
4
UP77-0031 5/16” Steel Washer
20
UP77-0158
1/4’’ x 1 1/2’’
Swedge Bolt
4
HarDWarE lIst
It is recommended to make sure you have all parts and hardware prior to assembly.
WARning!
Read USAge inStRUCtiOnS & WARningS on pages 2-4, and 6-7 prior to assembly of this product! Failure to follow the
instructions on this page and pages 2-4, and 6-7 may result in serious injury or death!
WARning!
DO nOt over tighten the hardware. Over tightening can lead to structural damage and may negatively affect the performance
of your stand. Failure to follow these instructions may result in serious injury or death!
Refer to pages 6-7 for installation instructions.
Fig. 2
Cam-Buckle Strap
(assembled)
Snap Pin
Snap Pin
Snap Pin
Snap Pin
Middle
Section
Middle
Section
Middle
Section
Bottom
Section
Top
Section
Cam-Buckle Strap
(assembled)
Cam-Buckle Strap
(assembled)
Cam-Buckle Strap
(assembled)
Cam-Buckle Strap
(assembled)
1" cam-Buckle
Strap
Swedge
Bolt
Section
Insert long strap through bottom
of buckle on short strap.
stEP 1.
Attach a U-bracket onto the rear of each
stick section using (2) 5/16” x 1 3/4” hex bolts, (4)
nylon washers, (4) steel washers & (2) 5/16” nylock
nuts. Tighten securely. (Fig. 1).
stEP 2.
Assemble the cam-Buckle straps (Fig.
2). These straps will be hooked to one side
of the U-bracket and hang freely until the
Ascender is ready to secure to the tree (Fig. 3).
stEP 3.
Connect
the top, middle and
bottom sections
using (4) 1/4’’ x 1
1/2’’ swedge bolts,
(4) nylon washers &
(4) 1/4’’ nylock nuts
(Fig. 4).
note:
Fig. 5 shows
front of female
section with the 1/4”
hex head assembled.
Fig. 1
Fig. 3
Swedge
Bolt
Section
Section
Swedge
Bolt
Assembly
Fig. 4
Fig. 5
U-Bracket
5/16” x 1 3/4”
hex bolt
Ladder Section
Steel washers
Section
