manualshive.com logo in svg

MTU MS150033/05E, Руководство по эксплуатации

Поделиться
Скачать
MTU MS150033/05E Скачать руководство пользователя страница 49

3.11 After stopping the engine – Putting the engine out of

operation

Preconditions

☑

MTU Fluids and Lubricants Specifications (A001061/..) are available.

After stopping the engine

Item

Action

Coolant circuit

Drain engine coolant (→ Page 168)
Drain mixture coolant (→ Page 174) if:
•

freezing temperatures are expected and the engine is to remain out of
service for an extended period, but coolant has no antifreeze additive;

•

the engine room is not heated;

•

the engine coolant is not maintained at a suitable temperature;

•

the antifreeze concentration is insufficient for the engine-room tem-
perature;

•

antifreeze concentration is 50 % and engine-room temperature is be-
low -40 °C.

Power supply to engine con-
trol system

Switch off.

Gas supply

Close gas shut-off valve.

Air intake and exhaust sys-
tems

If the engine is to remain out of service for more than 1 week, seal the en-
gine's air and exhaust sides. If the engine is to remain out of service for more
than 1 month, carry out preservation (→ MTU Preservation and Represerva-
tion Specifications A001070/..).
The corrosion-inhibiting effect of the engine coolant may be used as an alter-
native in case of out-of-service periods lasting for more than 1 month, by run-
ning the engine for at least 2 hours at rated power once a month.

Starter battery (batteries)

Charge regularly (trickle charge).

Control-voltage battery (bat-
teries)

If fitted: Charge regularly (trickle charge).

Table 35: After stopping the engine

MS150033/05E 2013-10

| Operation | 49

TIM-ID: 0000043160 - 003

Содержание MS150033/05E






























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды