MTU 20V4000Bx4 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 304

background image

8.3.2 Crankcase breather – Filter element replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 4–20 Nm

F30044239

1

Ratchet bit

F30027340

1

Assembly compound (Kluthe Hakuform 30-15)

X00067260

1

Engine oil
Filter element

(→ Spare Parts Catalog)

3

O-ring

(→ Spare Parts Catalog)

3

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Replacing filter element

1.

Loosen clamps (1) from rubber sleeve (2) and
remove hose from cover (3).

2.

Loosen clamp (6) and remove cover (3).

3.

Remove air filter (5) with filter mounts (4).

4.

Remove O-ring (7) from adapter.

5.

Coat new O-ring (7) with assembly compound
and insert in groove on adapter.

6.

Insert filter holder (4) in correct position in
adapter.

7.

Place new air filter (5) in correct position on
filter holder (4).

8.

Insert filter holder (4) in correct position in
cover (3) and fit cover (3).

9.

Coat thread and nut mating face on clamp (6)
with engine oil.

10.

Tighten clamp (6) to specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Clamp

Tightening torque

9 Nm +1 Nm

11.

Install hose and tighten clamp (1) on rubber sleeve (2) to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Clamp

Tightening torque

5 Nm +1 Nm

12.

Replace other filter elements in the same way.

184 | Crankcase Breather | MS15039/01E 2018-11

TIM-ID: 0000077537 - 002

«
...
184
185
186
187
188
...
»

Содержание 20V4000Bx4

















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 20V4000Bx4

Бренд: Painless Performance Страницы: 24

Бренд: Schweigen Страницы: 28

Бренд: Saito Страницы: 2

Бренд: Yanmar Страницы: 104

EM-PMI540-T4000

Бренд: Danfoss Страницы: 71

Бренд: Clarke Страницы: 18

Бренд: ARRI Страницы: 28

Бренд: Clinton Страницы: 24

Бренд: INDUSTRIAS TECHNOFLEX Страницы: 40

Бренд: Fagor Страницы: 174

Бренд: Valach Страницы: 24

Бренд: Yanmar Страницы: 65

Бренд: O.S. Speed Страницы: 20

Бренд: O.S. engine Страницы: 23

Бренд: DLE Страницы: 4

Бренд: ZIEHL-ABEGG Страницы: 8

Бренд: Cuyuna Страницы: 51

Бренд: MTU Страницы: 257

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды