MTI FREEDOM FOCUS Скачать руководство пользователя страница 17

17

 MTI P/N 063-00370 rev A ©2021 MTI All Rights Reserved

www.MTIGS.com  |  T:800.426.6844

RECHARGEABLE LITHIUM BATTERY SAFETY GUIDELINES

DANGER

• 

LITHIUM-ION BATTERIES CAN POSE A RISK OF FIRE, PROPERTY DAMAGE AND 

SERIOUS INJURY IF DAMAGED OR USED PAST THEIR EFFECTIVE LIFE (USUALLY 14 

MONTHS).

• 

STOP USING THE BATTERY IMMEDIATELY AND STOP CHARGING THE BATTERY IF 

ABNORMAL HEAT, ODOR, DISCOLORATION, DEFORMATION/SWELLING OR ANY OTHER 

ABNORMAL CONDITION IS DETECTED.

• 

Thoroughly read the user’s manual before use, as inaccurate handling, storage or use of 

lithium-ion rechargeable batteries may cause leakage, heat, smoke, fire, or degrade battery 

performance.  

• 

Lithium-Ion batteries have finite life cycles. If the time that the battery powers equipment 

between charges becomes shorter than usual, the battery life is at an end. Remove device 

from service and contact MTI for guidance on replacement options.

CAUTION

• 

Keep away from heat or open flame, especially if leakage or an odor is detected. 

• 

When not using the battery for an extended period, remove the electronic device from 

service and store in a place with low humidity and controlled room temperature.  Keep 

the cells in 50% charged state during long period storage. Recommend maintenance is 

to charge the battery up to 50% of the total capacity every 3 months after receipt of the 

battery and maintain the voltage 3.7~4.0V. 

• 

Extended or improper storage can result in degraded battery performance and increased risk 

of failure.

FIRST AID MEASURES

• 

In case of battery rupture, evacuate personnel from contaminated area and provide 

maximum ventilation to clear out fumes and gases. Avoid contact with any liquid leaking 

from the battery.

• 

If liquid leaks onto your skin or clothes, immediately flush affected areas with plenty of 

water and soap for at least 15 minutes and seek medical attention. Do not apply ointments 

unless instructed by a doctor. 

• 

If liquid is leaking from the battery cell gets into your eyes, do not rub your eyes. 

Immediately flush with plenty of water (eyelids-held open) for at least 15 minutes and seek 

medical attention. 

Safety Warnings and Precautions

-CONTROLLED DOCUMENT-

063-00370

A-0

Status: Approved

Содержание FREEDOM FOCUS


















Отзывы: