background image

CX FLEX

™ 4A 

PRODUCT MANUAL

4

 MTI P/N 063-00318 rev A ©2019 MTI All Rights Reserved

www.mtigs.com  |  T:800.426.6844

MERCHANDISING

KEY ENROLLMENT

Place Authorization Card over the 
RFID icon to register to system. 
LED will be solid blue.

System must be disarmed 

to perform this operation.

Place the User Key you want to 
add over the RFID icon.
If successful 

 unit beeps 2 times

Repeat process for all User Keys 
until they are successfully added.

To close Enrollment mode, place 
the Authorization Card over the 
RFID icon. Enrollment mode will 
end automatically after 3 minutes 
of no use. LED will then be 
intermittently flashing white.

NOTE: The Type-C 

terminals do not  

deliver power or 

transfer data to any 

device.

1

1

3

2

3

USB-C Sensor:

 Insert the other end of the cable into 

the device.

Plug the USB-C system end (marked with the MTI 
logo) of the sensor into the CX Flex until it clicks.

Flexi-Disc Sensor:

 Peel the red film from the VHB 

adhesive and press firmly onto the product for 1 
minute if the product surface is curved, or 30 seconds 
if it is flat.

System will auto-arm after 1 minute, or arm 
immediately by holding an enrolled User Card over the 
RFID Icon.

click

2b

2a

Содержание CX FLEX 4A











Отзывы: