background image

24

MTH SD40-2 Diesel Operating Manual

To lock in the setting, simply turn the throttle all the way off and then back
on again.

To turn the Remote Lockout Control setting back off, go back to

Feature 40 and press the whistle button until only one bell ding sounds. To
lock in the setting, simply turn the transformer throttle off and then back on
again. Alternatively, you can go to RESET Feature 18 to reset all
ProtoSound® features back to their original factory defaults including
Remote Lockout Control.

RESETTING ALL PROTOSOUND OPTIONS TO
FACTORY DEFAULTS

ProtoSounds® is equipped with

a RESET feature (Feature 18)
that resets all programmable
options back to their original
factory settings. This is a useful
feature if you find your engine
not operating the way you think it
should and don’t want to take the time to check each RESET feature one at
a time. To reset all the RESET features back to their original factory
settings, enter RESET and go to Feature 18. (See the section entitled Using
RESET To Program ProtoSounds® 
on page 18). Once in Feature 18,
press the transformer whistle button and wait for ProtoSounds® to sound a
garbled bell sound. Then interrupt the throttle to enter forward.

TURNING OFF CAB CHATTER SOUNDS

“Cab Chatter" sounds occur in the neutral position every 2 to 30 seconds.

There are four “Chatter" messages which play at random times. This helps
to eliminate repetitive and boring messages. While the sounds are selected
to play randomly by the unit’s computer, there is no guarantee that you
won’t hear the same message repeated twice or more times. If you don’t
want to hear the Cab Chatter sounds, they can be turned off through Feature
23. To turn off the Cab Chatter sounds, enter RESET and go to Feature 23.
(See the section Using RESET To Program ProtoSounds® on Page 17.)
Once in Feature 23, press the transformer whistle button and wait for
ProtoSounds® to sound a bell ding(s). Continue pressing the whistle button
until ProtoSounds® sounds two bell dings (signifying that the module has
been programmed to turn the Cab Chatter off). Simply turn the transformer
throttle off and then on again to lock in your selection. To turn the Cab
Chatter sounds back on again, repeat the above process, but keep pressing
the transformer whistle button in Feature 23 until ProtoSounds® only
sounds one bell ding.

Clank,

Clank,

Etc.

In RESET Mode

Move The Throttle

Up & Down From

High Voltage To Low

18 Times

Listen For 3 Clank

And 3 Clink Sounds

Push The Whistle Button

Until You Hear

A Warbled Bell Ding

Interrupt The Throttle

To “Lock-In”

The Default Setting

H

Содержание 20-2162-1





































Отзывы: