MTHTrains 10-1091-1 Скачать руководство пользователя страница 28

Страница: 28 / 31

MTH 392E Operating Manual

TINPLA

PROTOSOUND RESET FEATURE CHART

The following chart lists the available features found in your ProtoSound equipped engine.

The default settings are listed for each feature as well as the operation of the feature. You can

reset all features to their original factory settings by accessing Feature 18 in RESET and then

pressing and holding the transformer whistle button until you hear a soft, warbled bell sound.

The FYS sound effects occassionally repeat

themselves.

ProtoSounds has a built--in random number generator

that randomly selects each sound clip to play.

Because there are only a total of 8 sound clips

available in each FYS event, it is probable that a

sound can occassionally be repeated one or more

times.

Once in FYS, the engine never goes in reverse.

So that the freight yard sound effects and operation is

as realistic as possible, ProtoSounds disables the

reverse unit state whenever FYS is enabled. This way

the engine never goes into reverse as the operator

cycles through the various FYS events.

When the engine enters FYS event 5, the bell

automatically comes on.

FYS has a built--in command to turn on the bell when

the system enters Event 5. After approximately 15

rings of the bell, it automatically will turn off.

RESET #

OPERATION

DEFAULT

CLANKS/CLINKS

Engine Volume

Full Volume

1 Clank/1 Clink

Coupler ON/OFF

Coupler ON

2 Clanks/0 Clinks

Reset Default Settings

3 Clanks/3 Clinks

Remote Bell Button

Bell Button Active

4 Clanks/0 Clinks

RESERVED

Whistle In Neutral

Whistle In Neutral OFF

5 Clanks/0 Clinks

Chuff Rate

Full Chuff Range

5 Clanks/2 Clinks

FYS Enabled

FYS ON

5 Clanks/3 Clinks

Lockout Enabled

Lockout OFF

8 Clanks/0 Clinks

Squeaking Brakes

Brakes Always ON

9 Clanks/0 Clinks

Содержание 10-1091-1
































Результаты поиска

Содержание 10-1091-1

Отзывы:

Бренды по названию

Популярные бренды

MTHTrains 10-1091-1, Руководство по эксплуатации

Результаты поиска

Содержание 10-1091-1

Отзывы:

Бренды по названию

Популярные бренды