MTH PUMPS T31 Series Скачать руководство пользователя страница 11

Страница: 11 / 16

Page 511

T31 CLOSE COUPLED PUMP

P2 BEARING PEDESTAL

Figure 5-3

5B Disassembly

The following tools and equipment are

needed for disassembly of the P2 unit:

Tools:

1. Soft plastic or wooden mallet.

2. Arbor press or vise.

3. 3/4" X 6" piece of water pipe.

4. Internal snap ring plier.

5. Penetrating oil.

BEARING PEDESTALS

Preliminary

Disassembly

Inspection of Components

Reassembly

Testing and Final Adjustments

5A Preliminary P2

1. Disconnect the inlet and outlet pip-

ing before unbolting the pump. If the

pipes are corroded, use penetrating

oil on the threads to aid in removal.

2. Unbolt the pump from the base and

remove. Disassembly instructions

for the pump are found in Section

5, T31 PUMP ENDS. All work on

the unit should be performed on an

elevated workbench whenever pos-

sible.

The disassembly and reassembly pro-

cedures are broken into two sections

covering the following units :

5B — Disassembly of the P2 Unit.

5D — Reassembly of the P2 Unit.

T31 SERIES

Service

NAME/DESCRIPTION

PART NO. QTY.

Bearing Pedestal

Snap Ring/
Bearing Retaining

Shaft

Flinger

Key Coupling

Ball Bearing/Inboard

Ball Bearing/Outboard

24A

Coupling Guard/Halves

Capscrew

NAME/DESCRIPTION PART NO. QTY.

Motor Bracket

"O" Ring/Casing

"O" Ring/Drain Plug

"O" Ring/Thru Bolt

Snap Ring

Impeller

Seal Rotating Element

Seal Stationary Seat

125

Thru Bolt

Pipe Plug

Key/Impeller Drive

Содержание T31 Series

















Результаты поиска

Содержание T31 Series

Отзывы:

Похожие инструкции для T31 Series

Бренды по названию

Популярные бренды

MTH PUMPS T31 Series, Руководство пользователя

Результаты поиска

Содержание T31 Series

Отзывы:

Похожие инструкции для T31 Series

Бренды по названию

Популярные бренды