MTD P805K, Руководство оператора

Страница: 16 / 48

16
Setting The Cruise Control
NOTE:
The cruise control feature should only be
utilized while traveling in the forward direction.
• Slowly depress the drive pedal until the desired
speed is achieved.
• Lightly depress the cruise control lever.
• While continuing to hold the cruise lever down, lift
your foot from the drive pedal (you should feel the
cruise latch engage).
• Once engaged, the cruise control lever and the
drive pedal will lock in the “down” position, and the
tractor will maintain the same forward speed.
NOTE:
Cruise control can not be set at the tractor’s
fastest ground speed. If the operator should attempt to
do so, the tractor will automatically decelerate to the
fastest optimal mowing ground speed.
To disengage the cruise control, either:
• Depress the brake pedal to disengage the cruise
control and stop the tractor.
• Lightly depress the drive pedal.
To change to the reverse direction when operating with
cruise control, depress the brake pedal to disengage
the cruise control and bring the tractor to a complete
stop. Place the shift lever in the REVERSE position and
depress the drive pedal.
Engaging the Parking Brake
To engage the parking brake:
• Fully depress the brake pedal and hold it while
gently pushing the parking brake lever downward.
• Hold the parking brake lever down while removing
your foot from the brake pedal.
• Once engaged, the parking brake lever and the
brake pedal will lock in the “down” position.
To disengage the parking brake:
• Slightly depress the brake pedal.
NOTE:
The parking brake must be engaged if the
operator leaves the seat with the engine running or the
engine will automatically shut off.
Engaging the PTO (Blades)
Engaging the PTO transfers power to the cutting deck
or other (separately available) attachments. To engage
the PTO, proceed as follows:
• Move the throttle control lever to the FAST (rabbit)
position.
• Pull the PTO/Blade Engage knob outward into the
engaged (ON) position. See Figure 7.
• Keep the throttle lever in the FAST (rabbit) position
for the most efficient use of the cutting deck or other
(separately available) attachments.
IMPORTANT:
With the ignition key in the NORMAL
MOWING position, the PTO clutch will automatically
shut off if the PTO (Blade Engage) knob is moved into
the engaged (ON) position with the shift lever in
Reverse. Refer to
Safety Interlock Switches on page 14.
Figure 7
Mowing
WARNING:
To help avoid blade contact or
a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop
machine if anyone enters the area.
This tractor is equipped with one of MTD ’ s quality
cutting decks. The following information will be helpful
when using the cutting deck with your tractor.
WARNING:
Plan your mowing pattern to
avoid discharge of materials toward roads,
sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or
obstruction which may cause discharged
material to ricochet back toward the operator.
• Do not mow at high ground speed, especially if a
mulch kit or grass collector is installed.
• For best results it is recommended that the first two
laps be cut with the discharge thrown towards the
center. After the first two laps, reverse the direction
to throw the discharge to the outside for the
balance of cutting. This will give a better
appearance to the lawn.
• Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
• Mowing should always be done with the engine at
full throttle.
• Under heavier conditions it may be necessary to go
back over the cut area a second time to get a clean
cut.
• Do NOT attempt to mow heavy brush and weeds
and extremely tall grass. Your tractor is designed to
mow lawns, NOT clear brush.
• Keep the blades sharp and replace the blades
when worn. Refer to
Cutting Blades on page 21 of this
manual for proper blade sharpening instructions.
ON
OFF
Front View Top View