manualshive.com logo in svg

MTD A0, Руководство оператора, Страница: 14 / 16

Поделиться
Скачать
MTD A0 Скачать руководство пользователя страница 14

Troubleshooting

5

14

Problem

Cause

Remedy

Engine fails to start

1.  Blade control disengaged.

2.  Spark plug boot disconnected.

3.  Fuel tank empty or stale fuel.

4.  Engine not primed (if equipped with primer). 

5.  Faulty spark plug.

6.  Blocked fuel line.

7.  Engine flooded. 

8.  Fuel valve (if equipped) closed. 

9.  Engine not choked (if equipped with choke).

1.  Engage blade control.

2.  Connect wire to spark boot.

3.  Fill tank with clean, fresh gasoline.

4.  Prime engine as instructed in the Engine 

Operator’s Manual.

5.  Clean, adjust gap, or replace.

6.  Clean fuel line.

7.  Wait a few minutes to restart; do not 

prime.

8.  Open fuel valve. See Engine Operator’s 

Manual.

9.  Choke engine. See Engine Operator’s Manual.

Engine fails to start with 

electric starter

(Electric Start Units Only)

1.  Electric Starter Push Key not fully inserted. 

2.  Battery not charged.

3.  Circuit breaker tripped.

1.  Insert Electric Starter Push Key into starter 

housing until it snaps into place.

2.  Charge battery.

3.  Debris may be blocking blade operation. 

Stop engine, remove Electric Starter Push 

Key, and disconnect spark plug boot. Verify 

grass or other debris are not obstructing 

the blade. Carefully clean out debris if 

necessary. Reattach spark plug boot and 

reinsert Electric Starter Push Key. Wait one 

minute after tripping for circuit breaker to 

automatically self-reset then reattempt start.

Engine runs erratic

1.  Spark plug boot loose.

2.  Blocked fuel line or stale fuel. 

3.  Vent in gas cap plugged.

4.  Water or dirt in fuel system.

5.  Dirty air cleaner.

6.  Unit running with CHOKE (if equipped) 

applied.

1.  Connect and tighten spark plug boot.

2.  Clean fuel line; fill tank with clean, fresh 

gasoline.

3.  Clear vent.

4.  Drain fuel tank. Refill with fresh fuel.

5.  Refer to Engine Operator’s Manual.

6.  Push CHOKE knob in.

Engine overheats

1.  Engine oil level low.

2.  Air flow restricted.

1.  Fill crankcase with proper oil.

2.  Clean area around and on top of engine.

Occasional skips

(hesitates) at

high speed

1.  Spark plug gap too close.

1.  Adjust spark plug gap. Refer to Engine 

Operator’s Manual.

Содержание A0

















Отзывы:

Нет отзывов