manualshive.com logo in svg

MTD 970 Series, Руководство оператора

Поделиться
Скачать
MTD 970 Series Скачать руководство пользователя страница 16

16

Figure 22

•

Make sure the belt is routed inside the pulley halves 
and the belt guard pin.

•

Reinstall the bolt securing transmission to rear 
mower housing.

•

Pivot the baffle back to its original position and 
secure with three hex screws removed earlier.

•

Lightly lubricate the inside of the blade adapter and 
reinstall the spacer, wave washer, blade adapter 
assembly, and blade in the correct order.

•

Tighten the hex bolt to secure the blade to torque: 
450-600 in. lbs.

Replacing Rear Flap 

•

To remove rear flap, cut off the flat end of the wire 
rod which secures it to the deck. 

•

Attach the new flap and new rod to deck, bending 
the ends of the new rod over to secure to deck.

SECTION 9:  OFF-SEASON STORAGE

Storing Your Lawn Mower

The following steps should be taken to prepare your 
lawn mower for storage.

•

Clean and lubricate mower thoroughly as described 
in the lubrication instructions.

IMPORTANT: 

We do not recommend the use of a 

pressure washer or garden hose to clean your unit.

•

Refer to engine manual for correct engine storage 
instructions.

•

Coat mower’s cutting blade with chassis grease to 
prevent rusting.

•

Store mower in a dry, clean area. Do not store next 
to corrosive materials, such as fertilizer.

NOTE: 

When storing any type of power equipment in a 

poorly ventilated or metal storage shed, care should be 
taken to rust-proof the equipment. Using a light oil or 
silicone, coat the equipment, especially cables and all 
moving parts.

Six-Speed
Cable Slot

Control
Arm

Содержание 970 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды