MTD 7100401 Скачать руководство пользователя

Страница: 13 / 44

4. Maintaining and cleaning works and the adjustment of the cutting height are only allowed when the motor and the cutting tools are stopped

or else with the sparking-plug-cap or power-slupply plug removed.

5. When leaving the mower, the motor must be stopped, or rather the power-supply-plug or ignition key are to be removed.

6. The safety distance given by the guide beams must be observed. The mower must only be operated when the guide beam is in a fixed

position.

7. Particular attention is necessary when mowing on slopes and declines.

8. Juveniles under 16 years are not allowed to operate the mower.

9. The operator of the mower must see to it that no other persons are in the working field.

10. Please take care of the appropriate maintenance, checking, and regrinding of the cutter according to the operating instructions.

11. An expert checking is necessary when, for instance, the mower comes immediately to a standstill by colliding with an obstacle .

12. Rotary mowers with an internal combusition engine must in no case be operated in closed rooms because of the poisoning danger.

13. Never refuel with the motor running. Do not smoke when you refuel. Take an appropriate funnel when you refuel so that no petrol can run

over on the motor and the housing or the lawn.

14. When you are mowing always wear solid shoes, no sandals or suchlike. Caution - there is a great risk of injury to fingers and feet when

the motor is running.

15. Please replace with suitable original blades only. Pay attention to instructions how to replace and regrind the blade.

INSTRUCTIONS FOR OPERATING

INSTRUCTIONS - MOTOR

Please follow the motor manufacturer's operating instructions. After starting: Adjust the accelerator lever slowly

into a position between START and STOP which you consider to be suitable operating speed. To switch on cutter bar. To switch on drive mechanism.

DANGER: When mowing beware of foreign bodies and impediments. If you should suddenly run into an unexpected impediment when mowing, please

switch of operating levers immediately. Stop cutter bar. After mowing for a short time switch the mower off and check that all nuts and bolts are tight.

Only mow with a sharp cutting edge and correct adjustment of all blades. To stop: Put the accelerator lever into STOP position.

HOW TO MOUNT THE ACCELERATOR WIRE (Fig. 2)

Position the lever (1) on the engine at the end of its stroke as shown by

arrow "A,, in the figure. Move the throttle lever (2) on the handlebar to the end of its stroke as shown by arrow "B,, in the figure. Insert wire (3) into hole

(4), secure the sheath (5) with retainer (6) and screw (7). ATTENTION: in the position "stop,, the throttle lever must stop engine.

BELT STRETCHER DRIVING WIRE (Fig.5)

Driving wire is already connected with the belt-stretching spring; have it connected to the

lever on handlebar as follows: Insert the wire (3) and the register (4) in hole cut in the prong. Engage sheath terminal (1) into hole (2).

ASSEMBLING OF THE CUTTER BAR (Fig.10-14)

For models equipped with 87 cm. cutting bar please complete the assembly adding

the missing sliding part ( part. 2 – fig. 10) you can find in the accessories envelope. In order to fix it please use the 2 screws ( part 1) , the washers

and the nuts you can find on the cutting bar. Please refer also to chapter : “ how to adjust the cutting bar height”. To fix part (7) with the parts (5, 6)

to the (8). Fix the part (10) with the parts (1, 2 and 3) to the (8). After about 2 hours of work to tighten the screws (5).

CORRECT ASSEMBLY OF THE BOWDEN ROD, ENGINE FUEL REGULATION (Fig. 3-4)

Insert the opposite end of the

Bowden rod down into the engine fuel lever. Now lightly clamp the jacketed end of the rod. Set the fuel lever on the handlebar to the start position