background image

 WARNING

 

1.  This cab is designed to provide foul weather protection only. It does not provide protection from 

noise, exhaust fumes, chemicals or injury from collision, rollover or other accidents. 

 
2.  Do not operate machine in confined areas without proper ventilation. 
 
3.  Thoroughly check area of operation before using machine. 
 
4.  The cab adds height to the machine. Low tree limbs and other overhead structures that did not 

interfere with the operation of the machine before, may now be obstacles. 

 
 

MAINTENANCE INSTRUCTIONS

 

A.  Periodically check all bolts to see that they are tight. If bolts become loose, failure of cab parts 

may occur. 

 

DO NOT CLEAN THE CLEAR PLASTIC WINDOWS WHEN THE PLASTIC IS DRY. 

THE CLEAR PLASTIC WILL SCRATCH.

 

 

B.  Avoid contact with plastic windows. Keep plastic windows clean by washing them with clear 

running water and rubbing with your bare hands, only. The use of a rag, sponge or brush will 
scratch the plastic. Liquid soap may also be used for window cleaning. During freezing weather, 
an automotive windshield washer solvent may be used. 

 
C.  Use liquid soap and water to clean colored vinyl portions. Scrubbing with a brush or rag is also 

permitted on the colored vinyl portions. 

 
 
 

STORAGE INSTRUCTIONS 

Prior to storage clean the windows and colored vinyl parts with a mild automotive detergent, rinse 
with clean water and allow to thoroughly dry, Store cab in a clean dry place out of direct sunlight. 
Avoid folding plastic windows. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

                   2 

Содержание 390-674-000









Отзывы: