MTD Pro calibration and, Инструкция по сборке

Страница: 9 / 10

9
Deflector Kit
MARK II DEFLECTOR KIT
INSTRUCTIONS
#01004434
1. Install the deflector mount (Ref.2) to the inside of
the main frame on the right hand side using 2-
bolts(Ref.,3)
& 2-nuts(Ref.1) as shown on page 2.
2. Slide deflector tube (Ref.6) & flat washer (Ref.20)
on to the deflector mount (Ref.2) insert cotter pin
(Ref.4) shown on page 2. Deflector tube (Ref.6)
must slide freely up & down deflector mount
(Ref.2).
3. Mount offset bracket (Ref.7) to deflector tube
(Ref.6) using 1-bolt (Ref.3) & 1-nut (Ref.1) as
shown on page 2.
4. Mount spacer (Ref.18) to the inside of the main
frame on the right hand side under, the lower
handle mount hole using 1-bolt (Ref.19),
flatwasher (Ref-9) 1-nut (Ref.17) & tighten, place
the deflector lift arm (Ref.8) between 2-nylon
washers (Ref.5) & with 1-nut (Ref.1) fasten so that
the lift arm will move firm but freely.
5. Connect the deflector lift arm (Ref.8) to the offset
bracket (Ref.7) using 1-bolt (Ref.3), 2-nylon
washers (Ref.6) & 1-mut (Ref.1) as shown on
page 2, fasten so that bolt slide freely in the slot of
the lift arm.
6. Mount the deflector adjusting bracket (Ref.11) to
the deflector lift arm (Ref.8) with 1-bolt (Ref.-.3) &
1-nut (Ref.1) fasten so that the adjusting bracket
will move firm but freely-
7. Install the operator lever (Ref.16) to the existing
dual remote bracket as shown on page 2, using 1-
bolt (Ref.3), 2--nylon washers (Ref.5) & 1-nut
(Ref.1) so that the lever will move firm but freely.
8. Mount the deflector control rod (Ref.14) to the
deflector adjusting bracket (Ref.11) using 1-nut
(Ref.13), 1-lockwasher (Ref.12) & 1-locknut
(Ref.10) as shown on page 2.
9. Slide the deflector control rod (Ref.14) through the
hole in the operator lever (Reil.16) & secure with
retainer clip (Ref.15).
10. Adjust nut (Ref.13) & locknut (Ref.10) so that the
deflector tube (Ref.6) moves to the top of the
deflector mount (Ref.2) when the operator lever
lightly snaps over center of it's pivot point.
Ref.
No.
Part No. Description Qty.
Ref.
No.
Part No. Description Qty.
1 00060036 Hex Nut, 1/4-20 Nylock SS 7 11 00030502 Deflector Adjusting Bracket 1
2 00030505 Deflector Mount Assembly 1 12 00060073 Lockwasher, 5/16 SS 1
3 00060057 Pan Hd. Mach. Scr. 1/4-20 x 7/8 6 13 00060071 Hex Nut, 5/16-18, SS 1
4 00061052 Cotter Pin, 1/8 x 1" SS 1 14 00030508 Deflector Control Rod 1
5 00018628 Flatwasher, 1/4 Nylon 6 15 00010171 C-Clip Retainer 1
6 00061066 Deflector Tube 1 16 00060034 Operating Lever and Rubber Han-
dle 1
7 00035030 Offset Bracket 1 17 00060059 Hex Nut, 1/4-20 SS 1
8 00030509 Deflector Lift Arm 1 18 00030503 Deflector Arm Mounting Spacer 1
9 00060033 Flatwasher, 1/4 SS 1 19 00060029 Machine Screw, 1/4-20 x 2 SS 1
10 00060072 Hex Nut, 5/16-18 Nylock SS 1 20 00061053 Flatwasher, 3/8 SS 1