background image

  WIRING FOR MSD-6 SERIES USING MAGNETIC TRIGGERING

Limited Warranty

 

M

SD IGNITION warrants this product to be free from defects in material and workmanship under its intended normal 

use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date 

of the original purchase. This warranty is void for any products purchased through auction websites. If found to be 

defective as mentioned above, it will be repaired or replaced at the option of MSD Ignition. Any item that is covered 

under this warranty will be returned free of charge using Ground shipping methods. 

  This shall constitute the sole remedy of the purchaser and the sole liability of MSD Ignition. To the extent permitted 

by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, 

including any implied warranty of merchantability or fitness. In no event shall MSD Ignition or its suppliers be liable 

for special or consequential damages.

  *Intended normal use means that this item is being used as was originally intended and for the original application 

as sold by MSD Ignition. Any modifications to this item or if it is used on an application other than what MSD Ignition 

markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item 

will work for the application they are intending. MSD Ignition will accept no liability for custom applications. 

service

  In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty. 

When returning MSD components for warranty service, 

Proof of Purchase must be supplied for verification. After 

the warranty period has expired, repair service is based on a minimum and maximum fee.

 

All  returns  must  have  a  Return  Material  Authorization  (RMA)  number

  issued  to  them  before 

being  returned.  To  obtain  an  RMA  number  please  contact  MSD  Customer  Service  at  1  (888)  MSD-7859  or 

visit  our  website  at  www.msdignition.com/rma  to  automatically  obtain  a  number  and  shipping  information. 

  When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include 

a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. 

The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered 

by warranty). For more information, call MSD Ignition at (915) 855-7123. MSD technicians are available from 7:00 

a.m. to 6:00 p.m. Monday - Friday (mountain time).

M S D   I G N I T I O N

  •   w w w . m s d i g n i t i o n . c o m  •   ( 9 1 5 )   8 5 7 - 5 2 0 0   •   FA X   ( 9 1 5 )   8 5 7 - 3 3 4 4

© 2007 Autotronic Controls Corporation

FRM29020 

 

 

 

 

Revised 10/07   

 

 

Printed in U.S.A.

INSTALLATION INSTRUCTIONS

R

Содержание 8962

Страница 1: ...sure is low and retard the timing during boost just enough to prevent knocking or predetonation Note In setting up the timing curve a hand held Mighty Vac or similar tool will allow you to simulate the boost pressure while you adjust timing at idle PROGRAMMING Cylinder Select The Boost Timing Master is programmed at the factory for 8 cylinder engines It can easily be modified for use on 4 and 6 cy...

Страница 2: ...If you already have a boost gauge you can tee into that line Adjusting the Boost The PN 8962 allows you to set the amount of ignition retard as well as when the retard begins both in relation to the amount of boost being produced Figure 3 Dash Control Knob This controls the slope of the retard That is how much timing is removed per pound of boost The settings are 0 3 of retard per pound of boost w...

Страница 3: ...able to get a good starting point to tune from Setting The Vacuum Advance 1 Make sure the advance timing knob is set to zero full counterclockwise and disconnect the pressure hose 2 With a timing light check your timing at idle This will be the timing the engine will see at low vacuum heavy throttle conditions 3 Shut off the engine and rotate the distributor to change timing in the advance directi...

Страница 4: ...ll be void It is the sole responsibility of the customer to determine that this item will work for the application they are intending MSD Ignition will accept no liability for custom applications Service In case of malfunction this MSD component will be repaired free of charge according to the terms of the warranty When returning MSD components for warranty service Proof of Purchase must be suppli...

Отзывы: