USING THE AIR MASK
8. As the battery cap makes contact with the battery car-
tridge, verify that the FireHawk M7 Responder HUD
display turns on and goes through its start up
sequence before turning off. The yellow LED should
not be flashing.
Battery Disposal/Recycling
Dispose of or recycle batteries in accordance with all
applicable federal, state, and local regulations.
DO NOT dispose of the batteries in fire. They may
explode. Failure to follow this warning can result in
serious personal injury or death.
Assembly of the FireHawk M7 Responder HUD to the
Facepiece Bracket
Note:
Assemble the FireHawk M7 Responder HUD to the
facepiece bracket before donning the air mask.
With the facepiece lying on its side:
1. Align the metal tab on the FireHawk M7 Responder
HUD with the metal plate on the front edge of the
bracket.
2. Rotate the FireHawk M7 Responder HUD so that the
tab falls into the slot behind the thumbscrew.
3. Thread the thumbscrew into the tab to finger-tight.
DO NOT use a screwdriver to tighten the thumbscrew.
Functional Tests
Note:
Refer to the Visual Inspection and Functional Test
section of this manual.
Always test the FireHawk M7 Responder HUD and the
entire air mask to be sure that the system operates
properly before entering any hazardous atmosphere.
DO NOT use this device unless it passes all inspection
and functional tests. Failure to follow this warning can
result in serious personal injury or death.
FIREHAWK M7 CONTROL MODULE FUNCTIONALITY
•
The FireHawk M7 Control Module is assembled to the
gauge line hose and is connected to the FireHawk M7
Power Module by the power cable. The FireHawk M7
Control Module serves as the user interface with the
air mask and it also serves as the wireless transmitter
for the FireHawk M7 Responder HUD.
•
The FireHawk M7 Control Module has three control
buttons.
o The RESET/OFF button (yellow) on the side of the
FireHawk M7 Control Module resets the PASS
device from the full alarm mode. It also shuts the
unit off after the cylinder valve has been closed and
all pressure is bled from the system. When the
optional FireHawk M7 Telemetry Module is used,
the Reset button allows the user to confirm an
evacuation command.
o The center lighted ALARM button (green/red) acti-
vates the full PASS alarm with or without air pressure.
o The top MODE button (green) will refresh the dis-
play in the FireHawk M7 Responder HUD, activate
the backlight on the display of the FireHawk M7
Control Module, set the FireHawk M7 Responder
HUD to continuous display mode, and toggle the
FireHawk M7 Control Module digital display mode
between pressure remaining and calculated service
time remaining. When the FireHawk M7 Control
Module is OFF, the mode button (green) can be
used to scan an ID Tag into the unit (when optional
FireHawk M7 Telemetry Module is used).
•
The FireHawk M7 Control Module turns on automati-
cally when the user opens the air mask cylinder valve.
As the system pressure reaches approximately 200
psi, both visible and audible alarms activate automati-
cally, indicating that the unit is functional (audible
alarms are emitted from the FireHawk M7 Power
Module located on the backplate). The unit remains in
monitor mode until the user closes the cylinder valve,
purges the system pressure, and presses the reset
button (yellow) on the side of the FireHawk M7 Control
Module two times within approximately one second.
•
While the air mask is in use, if the user is motionless
for approximately 20 seconds, the PASS (FireHawk
M7 Control Module and FireHawk M7 Power Module)
enters pre-alarm. During pre-alarm, the FireHawk M7
Power Module sounds 3 progressively louder tones
and the alarm button on the center of the FireHawk
M7 Control Module and buddy lights on the FireHawk
M7 Power Module slowly flash red. Also, during the
PASS pre-alarm, an orange LED will be displayed in
the FireHawk M7 Responder HUD. Movement of the
FireHawk M7 Control Module cancels the PASS pre-
alarm.
•
If the user remains motionless for 30 seconds (approx-
imately), the PASS enters full alarm. During full PASS
alarm, the FireHawk M7 Power Module repeatedly
sounds two high-pitched tones followed by a buzz.
During full PASS alarm the alarm button on the
FireHawk M7 Control Module and the buddy lights on
the FireHawk M7 Power Module rapidly flash red.
•
The PASS can be set into full alarm at any time (even
without air pressure) by pressing and holding the
alarm button on the FireHawk M7 Control Module.
•
The PASS function uses red and green LEDs behind
the alarm button of the FireHawk M7 Control Module
and buddy lights on the FireHawk M7 Power Module
to display its status visually:
o Green LEDs start to flash when the cylinder valve is
25
TAL 803 (L) Rev. 1 - 10086011
Содержание FireHawk M7 Responder
