manualshive.com logo in svg

MS Sedco DH100-CT, Руководство по установке

Поделиться
Скачать
MS Sedco DH100-CT Скачать руководство пользователя страница 8

Section 13

External Dimensions

Section 14

Warranty

MS SEDCO guarantees this product to be free from manufacturing 

defects for 3 years from date of installation.  Unless MS SEDCO is 

notified of the date of installation, the warranty will be in effect for 

3 years from the date of shipment from our factory.  If, during the 

first 3 years, our motion detector or support device fails to operate 

and has not been tampered with our abused, the unit can be 

returned prepaid to factory and it will be repaired free of charge.  

After 3 years, the unit will be repaired for a nominal service charge.  

This limited warranty is in lieu of all other warranties expressed 

or implied, including any implied warranty of merchantability, 

and no representative or person is authorized to assume for MS 

SEDCO any other liability in connection with the sale of our 

products.  All warranties are limited to the duration of this 

written warranty.  In no event shall MS SEDCO be liable for any 

special, incidental, consequential or other damages arising from 

any claimed breach of warranty as to its products or services.

Page 8

(/MANU) DH100-CTv1017

Sliding Pedestrian Door Motion & Presence Sensor 

INSTALLATION INSTRUCTIONS

DH100-CT

7898 Zionsville Road 

 Indianapolis, Indiana 46268

Telephone: (317) 842-2545 

 www.mssedco.com 

 [email protected]

75mm(2.95")

 

=

 

Standard

 

Mounting

 

Pitch

25mm

(0.98")

15mm

(0.59")

35mm

(1.37")

10mm

(0.39")

230mm(9.06")

44mm

(1.73")

70

.4

 

m

m

(2

.7

7"

)

66

.5

 

m

m

(2

.6

2"

)

33.5

 

mm

(1.32")

Содержание DH100-CT










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды