MrCool MWUC 5 Series Скачать руководство пользователя страница 14

Страница: 14 / 33

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT-

Save these instructions

for

local inspector

’

s use.

IMPORTANT-

Ensure installation follows all local

and state codes and ordinances.

Note to Installer- Be sure to leave these

instructions with the consumer.

Note to consumer- Keep these instructions

for future reference.

Skill level- Installation of this appliance requires

basic mechanical skills.

Completion time- Approximately 1 hour.

We recommend that two people install this

product.

Proper installation is the responsibility of

the installer.

Product failure due to improper installation is

not covered under the Warranty. You MUST use

only the parts supplied, along with proper

installation procedures as described in this

manual, when installing this air conditioner.

TOOLS YOU WILL NEED

Phillips

Screwdriver

Level

Flat Head

Screwdriver

Pencil

Ruler or tape

measure

Scissors or knife

WINDOW REQUIREMENTS

Your air conditioner is designed to install in

standard double hung windows, with

opening widths of 22 to 36 inches

(559 mm to 914 mm) and a minimum

window height of 13.75 inches (349 mm).

Before you begin the installation, ensure

the window you have selected for the unit

meets this requirement.

NOTE:

Save the carton/box the air conditioner came

in as well as these Installation Instructions for

future reference. The carton/box is the best

way to store the unit during winter, or when

not in use.

The lower portion of the window (sash) must

be able to open enough to allow a vertical

opening of 13.75 inches (349.25 mm). The

rear of the A/C and side louvers must have no

obstructions and clean air around them to

allow enough airﬂow to ﬂow through the

condenser, for heat removal. The rear of the

unit must be outdoors, not inside a building

or garage. Find the center of your window and

lightly mark it with a pencil.

PREPARE THE WINDOW

•

•
•

•

mrcool.com

Installation Instructions

Page 13

Drill and

1/8” drill bit

Proper PPE

Wooden Windows

INNER

WINDOW SILL

INTERIOR

WALL

13.75" min

(349 mm)

22" to 36"

(559 mm to 914mm)

SEAL FOAM

Vinyl-Clad Windows

INNER

WINDOW SILL

13.75" min

(349 mm)

22" to 36"

(558 mm to 914mm)

SEAL FOAM

•

Содержание MWUC 5 Series


































Результаты поиска

Содержание MWUC 5 Series

Отзывы:

Бренды по названию

Популярные бренды

MrCool MWUC 5 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MWUC 5 Series

Отзывы:

Бренды по названию

Популярные бренды