background image

Points for Attention to Operation 

1.

 

The Spectro 96  Fluorospectrophotometer  is  suitably  used

  in  a  laboratory  room  to  perform 

analytical  measurements.  If  the  instrument  needs  to  be  used  at  a  worksite,  the  working 
environment of the worksite should accord with the demands of the laboratory environment 
basically. 

2. If the user needs to move the instrument to other working site for analytical  measurements, 

please use original packing materials on moving. 

3.  Be  sure  to  turn  on

off  the  power  of  the  instrument  according  to  the  operating  procedure. 

When starting up the instrument, please turn on the power source of the xenon lamp first. 
Then turn on the power source of the spectrophotometer main unit after the xenon lamp is 
lit.  When  shutting  down  the  instrument,  please  turn  off  the  power  source  of  the 
spectrophotometer  first  and  then  the  power  source  of  the  xenon  lamp.  Otherwise,  the 
instrument may not work normally. After the xenon lamp is lit, it is necessary to wait for 30 
minutes over till the lamplight becomes stable. After the power source of the xenon lamp is 
turned  off,  please  wait  for  60  seconds,  and  then  turn  on  the  lamp  if  the  lamp  needs  to  be 
used again.   

4.  When  the  power  source  of  the  xenon  lamp  is  turned  on  but  the  lamp  fails  to  be  lit  and  a 

squeaking  sound  of  high  frequency  or  a  cracking  sound  of  sparking  is  produced 
continuously,  please  turn  off  the  power  source  of  xenon  lamp  immediately  and  wait  for 
several seconds, then turn on the lamp again. Because the life of the xenon lamp is closely 
related  to  the  number  of  on-off  of  the  lamp  power  source,  the  lamp  should  avoid  being 
turned on/off repeatedly under a high voltage and the unnecessary number of on/off of the 
xenon lamp power source should be cut down as far as possible. 

5.

 

When the instrument is working, the surface temperature of the heat dissipation opening at 
the top of the left back side of the instrument (xenon lamp position) becomes very high. Be 
sure not to touch the surface of the heat dissipation opening with hands in order not to be 
burnt. The air around the heat dissipation opening should be kept circulating. 

6.

 

After each startup of the instrument, please first confirm that the heat dissipation fan at the 
side  of  the  instrument  runs  normally  in  order  to  ensure  normal  work  of  the  instrument.  If 
the user finds anything wrong with the heat dissipation fan, the instrument should be closed 
down for an overhaul. 

7.

 

In order to protect the photomultiplier when PMT level is higher (>6), do not let high light 
pass into the sample compartment. When a sample of unknown concentration is measured, 
PMT level should be set from low grade to high grade (1-17) gradually. 

8.

 

After  PMT  level  is  adjusted,  the  original  set  for  zero-point  of  fluorescence  should  be 
checked and note that zero-point adjustment may be needed again. 

9.

 

When  and  only  when  a  computer  error  is  due  to  the  operator¹s  false  operation  or  other 
interferences,  the  power  switch  of  the  spectrophotometer  main  unit  should  be  turned  off 
immediately.  When  the  software  cannot  be  operated,  please  use  task  manager  to  end  the 
“f96pc.exe” process, then restart the software and the instrument. 

10.

 

Within the monochromator the tightened screws must not be loosened. The optical devices 
and the working environment of the instrument should be kept clean. 

11.

 

When  opening  the  cover  to  inspect  the  instrument,  be  sure  to  turn  off  the  power  source. 
Particularly  after  the  upper  cover  of  the  instrument  is  removed,  as  there  are  electrical 
appliance parts with high voltage located at the left back of the instrument base, be sure not 
to contact these parts while the power source is still turned on. 

 

 

INSTRUCTION MANUAL    FOR SPECTRO 96 FLUOROSPECTROPHOTOMETER 

Содержание SPECTRO-96



























































Отзывы: