MR VACUTAP VR Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 268

background image

5 Assembly: Standard design

Maschinenfabrik Reinhausen GmbH 2015

40

4349315/00 EN

VACUTAP® VR®

Assembly: Standard design

WARNING

Risk of crushing from moving parts!

When the on-load tap-changer undertakes a tap-change operation, compo-
nents move on the selector and change-over selector, some of which are
freely accessible. Reaching into the selector or change-over selector during
a tap-change operation may result in serious injuries.
► Keep at a safe distance of at least 1 m during tap-change operations.
► Do not reach into the selector or change-over selector during tap-

change operations.

► Do not switch the on-load tap-changer when working on the selector

and change-over selector.

This chapter describes how to install a standard design on-load tap-changer
in a transformer and how to dry it.

Preparatory work

Perform the work stated below before installing the on-load tap-changer in
the transformer.

Fitting mounting flange on transformer cover

A mounting flange is required for fitting the on-load tap-changer head on the
transformer cover. This can be supplied as an option or can be produced by
the customer. Mounting flanges made by the customer must comply with the
installation drawings in the appendix.
►

NOTICE!

Fit mounting flange on transformer cover (pressure tight).En-

sure that the sealing face makes complete contact and is not damaged.

Figure 16: Mounting flange

5

5.1

5.1.1

«
...
38
39
40
41
42
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Cadman Страницы: 66

Бренд: B&K Страницы: 12

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Nektar Страницы: 3

Бренд: Eaton Страницы: 5

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: Zimmer Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды