MR VACUTAP VR-Ex Скачать руководство пользователя страница 214 | Manualshive

Страница: 214 / 256

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

214

7545652/00 EN

VACUTAP

®

VR-Ex

Prior to commissioning the transformer, check whether the motor-drive unit
and on-load tap-changer are correctly coupled and that the motor-drive unit
functions correctly.

Tests on the motor-drive unit

1. Perform function checks as described in relevant MR operating instruc-

tions for motor-drive unit.

2.

NOTICE!

An incorrectly coupled motor-drive unit will lead to damage to

the on-load tap-changer. Undertake trial tap-change operations across the
entire range of settings. Ensure that in each operating position, the tap po-
sition indicators of motor-drive unit and on-load tap-changer (inspection
window in the on-load tap-changer head) match.

Dielectric tests on transformer wiring

► Note information relating to dielectric tests on transformer wiring in rele-

vant MR operating instructions for motor-drive unit.

6.1.4 High-voltage tests on the transformer

Note the following points before performing high-voltage tests on the trans-
former:

▪ Ensure that the oil compartment of the on-load tap-changer is completely

filled with insulating fluid.

▪ Ensure that all protective devices for the on-load tap-changer are function-

ing correctly and are ready for use.

▪ Ensure that the ground connections on the motor-drive protective housing

and protective housing fastening are free of paint.

▪ Only perform high voltage test if motor-drive unit door is closed.

▪ Disconnect external connections to electronic components in the motor-

drive unit to prevent damage from overvoltage.

▪ When connecting the motor-drive unit's supply voltage, only use the cable

bushings in the protective housing base intended for lead insertion.

▪ Guide all ground connecting leads to one central connection point (estab-

lishment of suitable reference earth).

▪ Disconnect all electronic components before the high voltage test. Before

a dielectric test of the wiring, remove all devices with a withstand voltage
of < 1000 V.

▪ Remove leads used for testing before the high voltage test as these func-

tion as antennas.

▪ Wherever possible, route the measurement leads and data leads sepa-

rately to the energy cables.

Contact the manufacturer if you have any questions about possible sources
of danger.

«
...
212
213
214
215
216
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: Badgematic Страницы: 28

Бренд: National Instruments Страницы: 73

Бренд: Gage Bilt Страницы: 28

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Siko Страницы: 36

Бренд: Dr.X Works Страницы: 14

Бренд: Wallenstein Страницы: 44

Бренд: Nexen Страницы: 5

Бренд: Background Images Страницы: 23

Power Defense PDG1 Series

Бренд: Eaton Страницы: 7

Бренд: Techne Страницы: 32

Бренд: HELVAR Страницы: 2

Бренд: Taktomat Страницы: 35

DeviceEdge AGX Orin Series

Бренд: Aetina Страницы: 24

Aseptic INNOVA Mini K

Бренд: INOXPA Страницы: 28

MAXCOIL HEFA 600 MAX

Бренд: DryAIR Страницы: 35

Бренд: LG Страницы: 2

Бренд: Advantech-DLoG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды