MR VACUTAP VR-Ex Скачать руководство пользователя страница 210 | Manualshive

Страница: 210 / 256

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

210

7545652/00 EN

VACUTAP

®

VR-Ex

6 Commissioning

WARNING

Danger of explosion!

Explosive gases in the oil compartment of the on-load tap-changer, trans-
former, pipework system, oil conservator and at the dehydrating breather
opening can deflagrate or explode and result in severe injury or death!

► Ensure that there are no ignition sources such as naked flame, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the trans-
former's immediate surroundings during commissioning and that none oc-
cur.

► Do not operate any electrical devices (e.g. risk of sparks from impact

wrench).

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

WARNING

Danger of explosion!

Overloading the on-load tap-changer can lead to explosion. Spraying hot in-
sulating fluid and flying parts can lead to death and serious injuries. Prop-
erty damage is highly probable.

► Ensure that the on-load tap-changer is not overloaded.

► Ensure use of the on-load tap-changer in accordance with section "Ap-

propriate use".

► Prevent operations outside of the permitted operating conditions by tak-

ing suitable measures.

6.1 Commissioning the on-load tap-changer at the transformer

manufacturer's site

Perform the following work and functional checks before commissioning the
transformer.

6.1.1 Bleeding on-load tap-changer head and suction pipe

6.1.1.1 Bleeding on-load tap-changer head

1. Open all forward valves and return valves in the pipe system.

«
...
208
209
210
211
212
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: Warner Electric Страницы: 14

Бренд: enz Страницы: 40

Бренд: Southwire Страницы: 15

CPX-AB-1-7/8-DN

Бренд: Festo Страницы: 2

Бренд: Mecc Alte spa Страницы: 34

Бренд: Chipsee Страницы: 14

Бренд: SAMCHULLY Страницы: 44

VPO Priming System

Бренд: Waterous Страницы: 56

CHALLENGER II Series

Бренд: M&R Страницы: 241

Бренд: Lenze Страницы: 88

Hydrobar Express 220

Бренд: LNS Страницы: 164

GQM2195C2E4R7BB12 Series

Бренд: Murata Страницы: 25

Бренд: Parker Страницы: 8

Heavy Duty Dust Buggy

Бренд: U.S.SAWS Страницы: 18

Бренд: RINGSPANN Страницы: 4

Бренд: RINGFEDER Страницы: 23

Бренд: Wood-mizer Страницы: 133

Бренд: Siemens Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды