MR VACUTAP VR-Ex Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 256

background image

2 Safety

Maschinenfabrik Reinhausen GmbH 2020

17

7545652/00 EN

VACUTAP

®

VR-Ex

2.5 Measures for ensuring compliance with explosion

protection requirements

2.5.1 Measures taken by the manufacturer

Maschinenfabrik Reinhausen has taken the following measures for ensuring
compliance with explosion protection requirements. You do not need to take
any special measures in this regard.

2.5.1.1 Quality of the insulating oil in the on-load tap-changer

The quality of the insulating oil required by IEC 60296 and the quality of the
synthetic esters required by IEC 61099 in the oil compartment of the on-load
tap-changer is ensured by using vacuum cells with transition resistors.

2.5.1.2 Monitoring the oil temperature in the diverter switch oil compartment

A temperature sensor is provided in the on-load tap-changer head cover for
monitoring the oil temperature in the diverter switch oil compartment. The
corresponding temperature monitoring relay is in the TAPMOTION® ED-Ex.

Temperature monitoring prevents further switching of the on-load tap-
changer when the maximum permitted temperature is reached. This maxi-
mum permitted temperature is factory-configured for each specific order for
all on-load tap-changer types (maximum 130 °C) and secured against acci-
dental incorrect adjustment.

2.5.2 Measures to be taken by the transformer manufacturer/operator

The following measures for ensuring compliance with explosion protection
requirements must be taken by the transformer manufacturer/operator.

2.5.2.1 Prescribed protective and drive components

Operate the on-load tap-changer only in conjunction with the following com-
ponents:

▪ Ex protective relay

▪ Ex motor-drive unit

▪ Ex drive shaft

«
...
15
16
17
18
19
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: OMCA Страницы: 72

Бренд: Xtralis Страницы: 26

AX2090-ND80 Series

Бренд: Beckhoff Страницы: 41

Бренд: Facom Страницы: 44

Бренд: STEINEL Страницы: 92

Бренд: LANCIER Monitoring Страницы: 56

Бренд: Huck Страницы: 14

Kwik-Way SVS II Deluxe

Бренд: Irontite Products Страницы: 52

Бренд: Balluff Страницы: 69

Бренд: ebm-papst Страницы: 14

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: eta Страницы: 32

MPS-8033 Series

Бренд: ILX Lightwave Страницы: 112

Бренд: SCHUNK Страницы: 32

Бренд: Spirax Sarco Страницы: 3

Бренд: PFlow Industries Страницы: 108

Бренд: OP Страницы: 59

Бренд: Keysight Technologies Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды