Mr.Ken MELA Скачать руководство пользователя страница 2

Installation must be carried out by a qualified electrician.

Turn off the electrical mains at the circuit breaker/fuse box.

Do not use power supply other than 220V / 50Hz.

This appliance must be earthed.

When mounting the fan, ensure that the safety wire is looped across the mounting

 bracket

.

The mounting

 bracket

 must be able to withhold a min. weight of 35 pounds.

The ceiling fan must be mounted at a min. height of 7.5 feet / 2.3m of clearance from 

the floor.

Do not place any objects in the path of the blades.

When all electrical connections are done, store all wires neatly.

Make sure that all screws and connections are tightly screwed and secured.

Note

This illustrations in this manual are for explanation purposes only and may differ from the 

actual unit. It is subjected to change without prior notice for further improvements.

Warning

This product is designed to use only those parts supplied with this product and/or accessories 

designated specifically for using with this product. Using parts and/or accessories not designated 

for using with this product could result in personal injury or property damage.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

I. IMPORTANT SAFETY INSTRUCTIONS

Содержание MELA














Отзывы: