background image

Installation instructions and Owner’s Manual

1

UNVENTED NATURAL GAS FIRED ROOM HEATER

Blue Flame Heaters

Plaque Heaters

Model #

Burn Rate

Model #

Burn Rate

MHBF10NG/TSBF10NG

10,000 Btu/hr

MHIR10NG/TSIR10NG

10,000 Btu/hr

MHBF20/NGT/TSBF20NGT

20,000 Btu/hr

MHIR20NGT/TSIR20NGT

20,000 Btu/hr

MHBF30

N

GT/TSBF30NGT

30,000 Btu/hr

MHIR30NGT/TSIR30NGT

30,000 Btu/hr

INSTALLATION INSTRUCTIONS
AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a
safe place for future reference. Do not allow anyone who has not read these instructions to
assemble, light, adjust or operate the heater.

MHIR10NG/
TSIR10NG

ENERCO GROUP, INC., 4560 W. 160

TH

 ST., CLEVELAND, OHIO 44135 · 216-916-3000

WARNING:  If the information in this manual is not followed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance

Do not touch an electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING:  This is an unvented gas-fired heater.  It uses air (oxygen) from the room in which it is installed.
Provisions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and
Ventilation section on page 3 of this manual.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage.  Refer to this manual for correct installation and operational procedures.  For assistance or additional
information consult a qualified installer, service agency, or gas supplier.

MHIR20NGT/
TSIR20NGT

MHBF30NGT/
TSBF30NGT

MHBF10NG/
TSBF10NG

MHIR30NGT/
TSIR30NGT

MHBF20NGT/
TSBF20NGT

70574     Rev. C    08/05

Содержание HeatStar TSBF20NGT

























Отзывы: