11.
12.
HOW TO STEAM MILK
1. Fill the
water tank
to the “MAX” marking with clean, filtered water.
2. Turn the coffeemaker ON by using the
power switch
on the side.
NOTE:
The
ready indicator
light will pulse while the coffeemaker heats up
and will turn solid when the coffeemaker is ready to use.
3. Fill a milk pitcher or cup about 1/3 to ½ full with cold milk.
NOTE:
Any type of milk can be used – soy, rice, almond, coconut, etc. – but
2% fat dairy milk creates the best froth.
4. Insert the
milk frothing wand
tip just below the surface of the milk.
5. Turn the
knob
to the
“steam”
position.
NOTE:
The
ready indicator
light will pulse while the water is heating
up. Once the coffeemaker reaches the correct temperature, the
ready
indicator
light will turn solid. Some water and steam may come out of
milk frothing wand
while the coffeemaker heats up.
6. Steam your milk until it reaches the desired texture and temperature.
NOTE
: Steaming milk makes a hissing noise.
7. When finished, turn the
knob
to the
“standby”
position. Then, remove the
milk frothing wand
from the milk pitcher or cup.
NOTE:
After steaming milk, the
knob
must be turned to the
“standby”
position until the
ready indicator
light turns solid. If the
knob
is turned
directly to the
“brew”
position after steaming milk, the coffeemaker will
beep, the
display
will go blank and the coffeemaker will not brew coffee.
To fix the error, the
knob
will need to be turned to the
“standby”
position
until the
ready indicator
light turns solid.
8. Remember to clean the
milk frothing wand
after every use. For instructions
on how to do so, please refer to the cleaning section on page 12.
9. Enjoy!
NOTE:
When the
knob
is turned to the
“standby”
position after steaming
milk, the coffeemaker will enter an automatic cool-down cycle that lasts
approximately 35 seconds. During this cycle, the
ready indicator
light
with pulse and water will be released into the
drip tray
though an internal
channel. Steam may be emitted from the
drip tray
. When the
ready
indicator
light turns solid, the coffeemaker has cooled down and is ready
to use.
Helpful Tips for Steaming Milk:
1. Insert the
milk frothing wand
tip just below the surface of the milk.
2. Position the
milk frothing wand
and milk pitcher or cup at an angle that
allows the milk to move in a whirlpool pattern.
3. As the milk level rises, lower the milk pitcher or cup to keep the
milk
frothing wand
tip just below the surface.
4. When the desired texture is achieved, immerse the
milk frothing wand
half way.
ROUTINE CLEANING
Make sure your coffeemaker is unplugged and has cooled completely before
cleaning. We recommend hand washing all removable parts to help preserve
their appearance.
Pot of Coffee
1. Remove the
brew basket
,
brew basket lid
,
filter
,
coffee pot
and
coffee
pot lid
and wash them with warm water and mild liquid soap. Dry
thoroughly.
Single Serve
1. Remove the
single serve portafilter
from the coffeemaker carefully and
dump any remaining water into the sink before lifting the lid. Then, discard
the K-Cup® Pod into the trash bin
2. Rinse the
single serve portafilter
with water, shake the water off and dry it
on the outside.
WARNING:
There is a sharp needle at the bottom of the
single serve
portafilter
.
Espresso
1. Remove the
espresso portafilter
from the coffeemaker. Then, release the
filter retainer clip
and press it over the
filter
. Hold it in place while you
tap the
espresso portafilter
against the trash bin to discard the espresso
grounds.
2. Remove the
filter
from the
espresso portafilter
by twisting the
filter
until the bump on the
filter
is aligned with the notch on the
espresso
portafilter
. Wash the
filter
and the
espresso portafilter
with warm water
and mild liquid soap.
3. Place the
filter
back into the
espresso portafilter
and insert the
espresso
portafilter
back into the coffeemaker. Follow the same steps for brewing
espresso, but with no espresso in the
filter
. Discard the water in the cup.
4. Remove the
espresso portafilter
from the coffeemaker. Dry the
filter
and
espresso portafilter
thoroughly.
Milk Frothing Wand
1. Remove the
milk frothing wand cover
and wash with warm water and
mild liquid soap.
2. With a damp cloth, wipe down the metal on the
milk frothing wand
.
3. Fill the
water tank
and place a jug under the
milk frothing wand
.
4. Turn the
knob
to the
“steam”
position and press the
clean
button. The
clean indicator
light will illuminate and the coffeemaker will enter a
2-minute clean cycle.
5. When the
clean indicator
light turns off, turn the
knob
to the
“standby”
position. The coffeemaker will then enter an automatic cool-down cycle
that lasts approximately 35 seconds.
TURN
TURN
BVMC-O-C_19ESM1.indd 11-12
5/24/19 09:16
