manualshive.com logo in svg

MQ Power WHISPERWELD DAW-500S, Руководство по эксплуатации и частям

Поделиться
Скачать
MQ Power WHISPERWELD DAW-500S Скачать руководство пользователя страница 24

PAGE 24 —DAW-500S  WELDER/A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #0 (07/19/01)

DAW-500S  — INSTRUMENTATION

Power Outlets

The welder/AC generator has the following single-phase 60
Hz, 120 volt receptacles.

Single Phase

One  Duplex NEMA (GFCI) 5-20R (120V, 20 Amp)

One Twist Lock NEMA L5-30R (120V, 30 Amp)

Main Circuit Breaker (Single-Pole)

This  single-pole, 25 amp breaker protects the welder/AC
generator from short circuiting or overloading from the 60
Hz single-phase load.

GFCI Protection Breaker (Single-Pole)

This  single-pole,  20  amp  breaker  protects  the  GFCI
receptacle from short circuiting or overloading.

CAUTION :

When  using  a  combination  of  dual
receptacles, total load should not exceed
the  rated  capacity  of  the  welder/AC
generator set.

Idle Control Switch

The DAW-500S Welder/AC generator is provided with an
automatic    idle    (engine)  control  capability  for  noise
suppression  and  fuel  cost  reduction.  The  automatic  idle
control  feature  automatically  engages  under  a  no-load
condition.

When the Idle Control Switch is placed in the “ON” position,
the engine revolutions will be approximately  2000 rpm (low-
speed operation). When a load is connected to one of the
output receptacles, the engine speed will a u t o m a t i c a l l y
increase to about 2800 rpm (high-speed operation) within 10
seconds. Conversely, when the load is removed, the engine
speed will automatically drop back down to 2000 rpm within
10 seconds.

With  AC  loads  of  more  than  150W  (such  as  lighting
equipment, motor-powered tools, submersible water pumps,
etc.), the engine runs at high speed.  When a no load condition
is produced, the engine automatically slows down.

Turn the idle control switch to the “ON” (up) position when
AC loads of more than 200W are connected. Turn the idle
control switch to the “OFF” (down) position when AC loads
of less than 100W or when a magnetic switch is used, or if
very high quality of welding result is required.

However, when welding in CV Low, the engine will continue
to run at a low speed, even when appling AC loads.

GFCI Receptacle

Before connecting a load to the generator's GFCI receptacle,

push 

the  "Test  Button"  on  the  front  of  receptacle  before

connecting  the  load,  to  confirm  that  the  receptacle  is
functioning correctly.

Содержание WHISPERWELD DAW-500S















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды