manualshive.com logo in svg

MQ Power Whisperwatt DCA36SPXU4F, Руководство по эксплуатации

Поделиться
Скачать
MQ Power Whisperwatt DCA36SPXU4F Скачать руководство пользователя страница 4

PAGE 4 — DCA36SPXU4F • OPERATION MANUAL — REV. #4 (09/18/19) 

SAFETY INFORMATION

Do not operate or service the equipment before reading the 

entire manual. Safety precautions should be followed at all 

times when operating this equipment. Failure to read and 

understand the safety messages and operating instructions 

could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you 

about potential hazards that could injure you or others. The 

safety messages specifi cally address the level of exposure 

to the operator and are preceded by one of four words: 

DANGER, WARNING, CAUTION 

or 

NOTICE.

SAFETY SYMBOLS

  DANGER 

Indicates a hazardous situation which, if not avoided, 

WILL

 result in 

DEATH

 or 

SERIOUS INJURY.

  WARNING 

Indicates a hazardous situation which, if not avoided, 

COULD

 result in 

DEATH 

or 

SERIOUS INJURY.

  CAUTION

Indicates a hazardous situation which, if not avoided, 

COULD

 result in 

MINOR

 or 

MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this 

equipment will be referenced with hazard symbols which 

may appear throughout this manual in conjunction with 

safety messages.

Содержание Whisperwatt DCA36SPXU4F















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды