manualshive.com logo in svg

MQ Power WHISPERWATT DCA125SSIU, Руководство по эксплуатации и запасным частям

Поделиться
Скачать
MQ Power WHISPERWATT DCA125SSIU Скачать руководство пользователя страница 23

DCA125SSIU 50 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (12/22/08) — PAGE 23

OUTPUT TERMINAL PANEL FAMILIARIZATION

100 VAC GFCI Receptacles

There are two 100 VAC, 20 amp GFCI (Duplex Nema 
5-20R) receptacles provided on the output terminal panel. 
These receptacles can be accessed in 

any voltage 

selector switch

 position. Each receptacle is protected by a 

20 amp circuit breaker. These breakers are located directly 
above the GFCI receptacles. Remember the load output 
(current) of both GFCI receptacles is dependent on the load 
requirements of the U, V, and W output terminal lugs.

Pressing the 

reset

 button resets the GFCI receptacle after 

being tripped. Pressing the 

test button

 (See Figure 7) in 

the center of the receptacle will check the GFCI function. 
Both receptacles should be tested at least once a month.

G.F.C.I. Receptacle

Figure 7. 

Twist Lock Dual Voltage 100/200 VAC Receptacles

There are three 100/200V, 50 amp auxiliary twist-lock (CS-
6369) receptacles (Figure 8) provided on the output 
terminal panel. These receptacles can 

only

 be accessed 

when the voltage selector switch is placed in the 

single-

phase 240/120 position.

100/200V Twist-Lock  Auxiliary 

Figure 8. 

Receptacles

Each auxiliary receptacle is protected by a 50 amp circuit 
breaker. These breakers are located directly above the 
GFCI receptacles. Remember the load output (current) on 
all three receptacles is dependent on the load requirements 
of the 

Output Terminal Lugs.

Turn the 

voltage regulator control knob

 (Figure 9) on the 

control panel to obtain the desired voltage. Turning the knob 
clockwise will 

increase

 the voltage, turning the knob 

counter-clockwise will 

decrease

 the voltage.

Voltage Regulator Control Knob

Figure 9. 

Содержание WHISPERWATT DCA125SSIU

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды