background image

DCA-180SSV— OPERATION AND PARTS MANUAL — REV. #1  (04/14/10) — PAGE 41

1

Service Daily

If the engine is operating in very 

dusty

 or 

dry grass

conditions, a clogged air cleaner will result. This can lead to
a  loss of power,  excessive carbon buildup in the combustion
chamber  and high fuel consumption. Change air cleaner
more 

frequently

 if these conditions exists.

Fuel Addition

Add diesel fuel (the grade may vary according to season
and locations).

Removing Water from the Fuel Tank

After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally inspect the fuel
tank for water contamination and drain the contents if
required.

During cold weather, the more empty volume inside the
tank, the easier it is for water to condense. This can be
reduced by keeping the tank full with diesel fuel.

Cleaning Inside the Fuel Tank

Drain the fuel inside the fuel tank completely. Using a spray
washer (Figure 57) wash out any deposits or debris that have
accumulated inside the fuel tank.

Figure 57. Fuel Tank Cleaning

Fuel Tank Inspection

In addition to cleaning the fuel tank, the following components
should be inspected for wear:

Rubber Suspension 

 

look for signs of wear or

deformity due to contact with oil. Replace the rubber
suspension if necessary.

Fuel Hoses 

 

inspect nylon and rubber hoses for signs

of wear, deteration and hardning.

Fuel Tank Lining 

 inspect the fuel tank lining for signs

of excessive amounts of oil or other foreign matter.

Cleaning the Fuel Strainer

Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.

Replacing Fuel Filter

Replace the fuel filter cartridge with new one every 500
hours or so.

Loosen the drain plug at the lower top of the fuel filter.
Drain the fuel in the fuel body together with the mixed
water. 

DO NOT

 spill the fuel during disassembly.

Vent any air

DCA-180SSV— MAINTENANCE

Содержание WHISPERWATT DCA-180SSV





















































































Отзывы: