MQ Power GA-9.7HEA Скачать руководство пользователя страница 24

Страница: 24 / 60

PAGE 24 — GA9.7HEA 60 HZ GENERATOR• OPERATION AND PARTS MANUAL — REV. #1 (09/18/19)

FUEL CHECK

1.  Close the fuel cock before filling the fuel tank.
2.  Remove the fuel cap located on top of fuel tank.
3.  Read the fuel gauge located on top of the fuel tank

(Figure 12) to determine if the fuel level is low. If fuel

is low, replenish with clean unleaded fuel.

Figure 12. Fuel Gauge

4. When refueling, be sure to use a strainer for filtration.

DO NOT

top-off fuel.

DO NOT

fill the tank beyond

capacity. Wipe up any spilled fuel

immediately!

BATTERY CHECK

ALWAYS

be sure the battery cables (Figure 13) are

properly connected to the battery terminals as shown below.

The

red cable

is connected to the positive terminal of the

battery, and the

black cable

is connected to the negative

terminal of the battery.

Figure 13. Battery Connections

NOTICE

Inadequate battery connections may cause poor

starting of the generator and create other malfunctions.

POSITIVE

NEGATIVE

NOTICE

ALWAYS

disconnect the negative terminal

first

and

reconnect negative terminal

last.

INSPECTION/SETUP

When connecting battery do the following:
1.

NEVER

use worn or damaged battery cables.

Replacedefective battery cables immediately.

2. Place a small amount of battery terminal treatment

compound around both battery terminals. This will

ensure a good connection and will help prevent

corrosion around the battery terminals.

POLARITY

The polarity of the battery is extremely important. When an

inverted circuit connection takes place, the circuit will be in

short circuit instantaneously resulting in possible damage

to the control box electronics and starter.
When connecting the battery cables to the battery terminals

be sure to check the polarity.

ALTERNATOR

The polarity of the alternator is negative grounding type.

When an inverted circuit connection takes place, the circuit

will be in short circuit instantaneously resulting in alternator

failure.

DO NOT

put water directly on the alternator. Entry of water

into the alternator can cause corrosion and damage the

alternator.

WIRING

Inspect the entire generator for bad or worn electrical wiring

or connections. If any wiring or connections are exposed

(insulation missing), replace wiring immediately.

PIPING AND HOSE CONNECTION

Inspect all piping, oil hose, and fuel hose connections for

wear and tightness. Tighten all hose clamps and check

hoses for leaks.
If any hose (

fuel or oil

) lines are defective, replace them

immediately.

NOTICE

If the battery cable is connected incorrectly, electrical

damage to the generator will occur. Pay close attention

to the polarity of the battery when connecting the battery.

Содержание GA-9.7HEA





























































Результаты поиска

Содержание GA-9.7HEA

Отзывы:

Похожие инструкции для GA-9.7HEA

Бренды по названию

Популярные бренды

MQ Power GA-9.7HEA, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание GA-9.7HEA

Отзывы:

Похожие инструкции для GA-9.7HEA

Бренды по названию

Популярные бренды