MQ Multiquip QP3TS Скачать руководство пользователя страница 14

Страница: 14 / 29

QP3TS TRASH PUMP • OPERATION MANUAL — REV. #0 (03/02/20) — PAGE 13

PUMP COMPONENTS

Figure 3 shows key components of the QPT3S Pump.
1.

Pump

— The model QP3TS is a 3-inch trash pump

used in general dewatering applications. Typical

dewatering applications consist of: manholes, septic

tanks, ponds, ditch water, silt water, muddy water, and

water with debris.

Fill Cap

— Prior to operation, the pump casing

MUST

filled with water. Remove this cap to add water to

the pump. After the initial prime, a sufficient amount of

water will be retained in the casing so that the operator

will not need to re-prime later.

Discharge Ports

— The pump is equipped with a 3”

male NPT thread discharge port. and can accommodate

discharge hose or pipe. Quick disconnect (Cam &

Groove lock) hose can be fitted onto the discharge

ports with an optional coupler (A300A).

Discharge Hose

— This pump is fitted with 3” male

NPT thread discharge port that can accommodate

either threaded discharge hose or pipe. Quick

disconnect (Cam & Groove lock) hose can be fitted onto

the discharge port with an optional coupler (A300A).

Make sure hose lays flat and are not kinked. Contact

MQ Sales Department for ordering information.

Suction Port

— This pump is fitted with a 3” male

NPT thread suction port and can accommodate either

a threaded or quick disconnect (Cam & Groove lock)

hose. For quick disconnect connections, an optional

coupler (A300A) is necessary. Contact MQ Parts

Department for ordering assistance.

Suction Hose

— Use only recommended suction

hose. This pump is fitted with a 3” male NPT thread

suction port and can accommodate threaded or quick

disconnect (Cam & Groove lock) suction hose. Cam

& Groove lock hose can be fitted onto the suction

port with an optional coupler (A300A). Make sure

the suction hose is not kinked. Contact MQ Sales

Department for ordering information.

Clean-out Cover

— When the pump is subjected to

applications where large quantity of debris is present,

it may be necessary to clean out the casing cavity of

large rocks and such that have not passed through the

pump. To open and gain access to the pump’s clean-out

cavity, loosen the four Locking Knobs (item 9). Grip the

cover handles and twist counterclockwise. Once the

cover is clear of the four knob fasteners, pull the cover

out towards you.

Drain Plug

— After usage, and for storage, remove

this plug and drain all water from the pump casing.

Locking Knobs

— Turn both knobs counterclockwise

to release cover. Turn clockwise to secure clean-out

cover.

10.

Strainer

— Always attach a strainer to bottom side of

the suction hose to prevent large objects and debris

from entering the pump. Strainer should be positioned

so that it will remain completely under water. Running

the pump with the strainer above water for long periods

can damage pump.

order

Discount-Equipment.com

Содержание QP3TS






























Результаты поиска

Содержание QP3TS

Отзывы:

Бренды по названию

Популярные бренды

MQ Multiquip QP3TS, Руководство по эксплуатации

Результаты поиска

Содержание QP3TS

Отзывы:

Бренды по названию

Популярные бренды